{"title":"Robotic Hands","description":"\u003cp\u003eFive-finger and three-finger dexterous hands from Unitree, BrainCo, Inspire, AgiBot, Linkerbot, Shadow and more — compared side by side by degrees of freedom, tactile sensing, weight and interface, and shipped worldwide.\u003c\/p\u003e","products":[{"product_id":"robotera-right-xhand1","title":"Robotera XHAND1 Dexterous Hand Right","description":"\u003cp\u003eThe Robotera XHAND1 Right is the right-hand version of Robotera's XHAND 1, a fully direct-drive dexterous robotic hand with 12 active degrees of freedom and no passive joints. Every joint has its own gear-driven, force-controlled joint module, three in the thumb, three in the index finger and two in each of the other fingers, so the thumb can oppose every finger down to the little finger and the index finger swings sideways from −5° to 17°.\u003c\/p\u003e\u003cp\u003eBecause all twelve joints are driven and backdrivable, with a linear relationship between motor current and torque, the hand suits reinforcement learning, imitation learning and force-control research: current-loop force control runs straight from the motors, and a finger gives way under an accidental knock instead of fighting it. Robotera supplies an SDK for C++, Python, ROS 1 and ROS 2 on Ubuntu, on x86 or ARM, and a URDF that includes tactile simulation for Isaac Gym and MuJoCo.\u003c\/p\u003e\u003cp\u003eEach fingertip is wrapped 270° in a 120-point tactile array that senses 3D force (normal and both tangential directions), temperature, contact area, vibration and slip trend, with accuracy down to 0.05 N. The hand grips with up to 15 N at a fingertip and 80 N with the whole hand, and in Robotera's lab tests one finger holds more than 5 kg, four fingers more than 20 kg and the whole hand lifts a 25 kg dumbbell. It responds at up to 10 clicks per second, and Robotera rates its direct gear drive faster than linkage- or tendon-driven designs.\u003c\/p\u003e\u003cp\u003eIt weighs 1,100 g and measures 191 × 94 × 47 mm, the size of an adult hand. EtherCAT and RS-485 over USB carry whole-hand control at 83 Hz on a 24–72 V supply drawing up to 2.5 A at 48 V, and the hand mounts with eight M3 screws around the wrist with the harness leaving at the side. Robotera names xArm, Realman and UR among compatible arms; fitment to your arm or humanoid is confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eThe \u003ca href=\"\/en\/products\/robotera-left-xhand1\"\u003eRobotera XHAND1 left hand\u003c\/a\u003e mirrors this one for two-handed teleoperation and bimanual research. The \u003ca href=\"\/en\/products\/robotera-xhand1\"\u003eRobotera XHAND1 Lite\u003c\/a\u003e is a different, lighter hand: 730 g, with 11 degrees of freedom, six of them driven. Compare all of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e12 active DoF, fully direct-drive:\u003c\/strong\u003e Twelve gear-driven, force-controlled joint modules, with no passive joints, let the thumb oppose every finger down to the little finger.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e270° tactile fingertips:\u003c\/strong\u003e Each fingertip carries a 120-point array that senses 3D force, temperature, contact area, vibration and slip trend, with accuracy to 0.05 N.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e80 N grip, 25 kg lift:\u003c\/strong\u003e The whole hand grips with up to 80 N and, in Robotera's lab tests, lifts a 25 kg dumbbell; a single fingertip reaches 15 N.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBackdrivable for learning:\u003c\/strong\u003e A linear current-torque relationship and backdrivable joints suit reinforcement learning, imitation learning and current-loop force control.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp to 10 clicks per second:\u003c\/strong\u003e Robotera rates its direct gear drive, with motors above 1 N·m of torque, faster than linkage- or tendon-driven designs.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eROS 1, ROS 2 and URDF:\u003c\/strong\u003e The SDK covers C++, Python, ROS 1 and ROS 2 on Ubuntu, and the URDF includes tactile simulation for Isaac Gym and MuJoCo.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT or RS-485:\u003c\/strong\u003e EtherCAT and RS-485 over USB run whole-hand control at 83 Hz on a 24–72 V supply.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"RobotEra","offers":[{"title":"Default Title","offer_id":67633017061606,"sku":"RobotEra-XHAND1","price":58500.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/robotera-xhand1_1_b1056df2-2451-448a-bed1-cd4028920986.jpg?v=1791277727"},{"product_id":"robotera-left-xhand1","title":"Robotera XHAND1 Dexterous Hand Left","description":"\u003cp\u003eThe Robotera XHAND1 Left is the left hand of Robotera's XHAND 1 dexterous robotic hand, and with the right hand it forms the pair that two-armed setups need: teleoperated data collection, bimanual manipulation research and humanoid upper bodies. Like the right hand, it has 12 active degrees of freedom, every one driven and none passive.\u003c\/p\u003e\u003cp\u003eRobotera built the XHAND 1 for teleoperation and learning. Its own retargeting software maps a human hand onto the XHAND from Vision Pro, Pico or Meta Quest headsets, Manus and other motion-capture gloves, or exoskeleton gloves, so operators can record demonstrations for imitation learning. The SDK covers C++, Python, ROS 1 and ROS 2 on Ubuntu, on x86 or ARM, and the URDF includes tactile simulation for Isaac Gym and MuJoCo.\u003c\/p\u003e\u003cp\u003eThe thumb and index finger have three joints each and the other three fingers two, each a gear-driven, force-controlled module with motor torque above 1 N·m. The index finger swings sideways from −5° to 17°, the thumb reaches the little finger in opposition, and the hand opens and closes more than twice a second with fingertips repeating to ±0.20 mm. The joints are backdrivable, which keeps the hand safe under impact and lets an operator move it by hand for kinesthetic teaching.\u003c\/p\u003e\u003cp\u003eFive 270° fingertip arrays, 120 points each, report normal and tangential force, temperature, contact area, vibration and slip trend. Maximum grip is 80 N for the whole hand and 15 N at a fingertip, with rated values of 24 N and 12 N, and in Robotera's lab tests the whole hand lifts a 25 kg dumbbell. At 1,100 g and 191 × 94 × 47 mm it runs on 24–72 V, connects over EtherCAT or RS-485 via USB with 83 Hz whole-hand control, and is rated for one million no-load grasp cycles from −20 to 60 °C.\u003c\/p\u003e\u003cp\u003eOrder it with the \u003ca href=\"\/en\/products\/robotera-right-xhand1\"\u003eRobotera XHAND1 right hand\u003c\/a\u003e for a matched pair. The \u003ca href=\"\/en\/products\/robotera-xhand1\"\u003eRobotera XHAND1 Lite\u003c\/a\u003e is Robotera's slimmer 730 g hand with 11 degrees of freedom. Compare the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLeft hand of a matched pair:\u003c\/strong\u003e With the XHAND1 right hand it gives a two-armed robot the same 12-DoF hand on both sides.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuilt for teleoperation:\u003c\/strong\u003e Robotera's retargeting software maps a human hand onto the XHAND from Vision Pro, Pico or Meta Quest headsets and Manus or exoskeleton gloves.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEvery joint driven:\u003c\/strong\u003e Twelve gear-driven, force-controlled joint modules with motors above 1 N·m, three each in the thumb and index finger and two in each other finger.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e120-point tactile arrays:\u003c\/strong\u003e A 270° array on each fingertip reads 3D force, temperature, contact area, vibration and slip trend.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp to 80 N grip:\u003c\/strong\u003e The whole hand grips with up to 80 N, a fingertip with 15 N, and the hand lifts a 25 kg dumbbell in Robotera's lab tests.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSDK for ROS 1 and ROS 2:\u003c\/strong\u003e C++ and Python on Ubuntu, on x86 or ARM, plus a URDF with tactile simulation for Isaac Gym and MuJoCo.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"RobotEra","offers":[{"title":"Default Title","offer_id":67633017159910,"sku":"RobotEra-Left-XHAND1","price":58500.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/robotera-xhand1-left.jpg?v=1791277726"},{"product_id":"inspire-robots-dexterous-right-hand-rh56f1","title":"Inspire RH56F1 Dexterous Hand Right (E2R)","description":"\u003cp\u003eThe Inspire RH56F1-E2R is the right hand of Inspire Robots' RH56F1 dexterous robotic hand, in the build without tactile sensors and with the E2 interface, EtherCAT plus RS-485. Ordered with the \u003ca href=\"\/en\/products\/inspire-robots-inspire-dexterous-left-hand-rh56f1\"\u003eRH56F1 left hand (E2L)\u003c\/a\u003e, it completes a matched pair for a two-armed humanoid or a dual-arm research cell; on its own, it gives a single right arm five fingers where a parallel gripper runs out of options.\u003c\/p\u003e\u003cp\u003eSix micro linear servo actuators move 12 joints: one actuator for each of the four fingers and two for the thumb, which bends and rotates laterally through 60–180°. The thumb rotates at more than 155°\/s and flexes at more than 37°\/s, the four fingers flex at more than 107°\/s, and a full close takes 0.8 s or less. All of it sits in an all-metal integrated skeleton with the wiring routed inside; the hand weighs 620 g and measures 183.3 mm long by 79.1 mm across the palm.\u003c\/p\u003e\u003cp\u003eEvery actuator carries its own force sensor, read at 0.1 N resolution, and that is how the hand grips: give each finger a force threshold and it closes until it reaches that force or its target position. Force closed-loop and impedance modes are there for soft or fragile objects that must be held without being crushed. Fingertips push with at least 15 N and the thumb with at least 10 N, they repeat to ±0.2 mm, and Inspire rates the passive payload at 30 kg after putting the series through 20 stringent tests.\u003c\/p\u003e\u003cp\u003eThe E2 interface runs 1 kHz real-time communication over EtherCAT, or RS-485 with Inspire's open register protocol or Modbus RTU, and up to 254 hands can share one RS-485 bus. Power is 24–48 V with a 5 A peak at 24 V. The wrist has an 8-pin aviation connector and four 3.5 mm through holes for mounting; fitment to your arm or humanoid is confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eNeed contact data as well as finger force? The \u003ca href=\"\/en\/products\/inspire-robots-inspire-dexterous-right-hand-with-tactile-sensors-rh56f1\"\u003eRH56F1 tactile right hand (E2R-T1)\u003c\/a\u003e adds eight capacitive tactile sensors in the fingertips and palm. For a stronger grip, the \u003ca href=\"\/en\/products\/inspire-rh56e2-dexterous-robot-hand\"\u003eInspire RH56E2\u003c\/a\u003e pushes 28 N per fingertip. See the whole range of \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRight hand with the E2 interface:\u003c\/strong\u003e The E2R mirrors the left-hand E2L and carries EtherCAT plus RS-485 with 1 kHz real-time communication.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eA force sensor on every actuator:\u003c\/strong\u003e Each of the six micro linear servo actuators reports force at 0.1 N resolution, so every finger can stop at a set force.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree grip control modes:\u003c\/strong\u003e Speed-force protection, force closed-loop and impedance control can be set finger by finger.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRigid metal frame at 620 g:\u003c\/strong\u003e An all-metal integrated skeleton with internal wiring keeps the hand at 620 g, 183.3 mm long and 79.1 mm across the palm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e15 N fingertips, 30 kg passive load:\u003c\/strong\u003e Fingertips push with at least 15 N and the thumb with at least 10 N, and Inspire rates the passive payload at 30 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCloses in 0.8 s:\u003c\/strong\u003e The four fingers flex at over 107°\/s and the thumb rotates through 60–180° at over 155°\/s, with fingertips repeating to ±0.2 mm.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Inspire Robots","offers":[{"title":"Default Title","offer_id":67633028858086,"sku":"Inspire-RH56F1-E2R","price":16700.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/inspire-robots-logo_5.jpg?v=1791277736"},{"product_id":"inspire-robots-inspire-dexterous-left-hand-rh56f1","title":"Inspire RH56F1 Dexterous Hand Left (E2L)","description":"\u003cp\u003eThe Inspire RH56F1-E2L is the left-hand version of Inspire Robots' RH56F1 dexterous robotic hand, in the build without tactile sensors. Its five fingers have 12 joints moved by 6 degrees of freedom, inside an all-metal integrated skeleton with the wiring concealed in the hand. It weighs 620 g and measures 183.3 mm long and 79.1 mm across the palm.\u003c\/p\u003e\u003cp\u003eInspire rates every fingertip at 15 N or more and the thumb at 10 N or more, rates the passive payload at 30 kg, and puts the series through 20 stringent tests. That suits humanoid builders and research labs that need a hand where a parallel gripper runs out: tool handles, cups and irregular parts, picked and held by one robot hand or by a left and right pair on a two-armed robot.\u003c\/p\u003e\u003cp\u003eForce is read at 0.1 N resolution and fingertips repeat to ±0.2 mm. The thumb rotates laterally through 60–180° at more than 155°\/s, the four fingers flex at more than 107°\/s, and the hand closes fully in 0.8 s or less. The E2 interface combines EtherCAT and RS-485 with 1 kHz real-time communication, on a 24–48 V supply drawing at most 5 A at 24 V. The wrist carries four 3.5 mm through holes for mounting, and fitment to your arm or humanoid is confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eThe \u003ca href=\"\/en\/products\/inspire-robots-dexterous-right-hand-rh56f1\"\u003eRH56F1 right hand (E2R)\u003c\/a\u003e mirrors this one for a two-handed setup. The \u003ca href=\"\/en\/products\/inspire-robots-inspire-dexterous-left-hand-with-tactile-sensors-rh56f1\"\u003eRH56F1 tactile left hand (E2L-T1)\u003c\/a\u003e and its right-hand twin add eight tactile sensors with a 30 N range and 5 % full-scale accuracy, for work that needs contact data; the E2L is the choice when position and force feedback are enough. Compare them with the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAll-metal skeleton at 620 g:\u003c\/strong\u003e An integrated metal frame with wiring concealed inside keeps the hand rigid at 620 g, 183.3 mm long and 79.1 mm across the palm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e15 N at every fingertip:\u003c\/strong\u003e Each fingertip pushes with at least 15 N and the thumb with at least 10 N, with force read at 0.1 N resolution.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e30 kg passive payload:\u003c\/strong\u003e Inspire rates the RH56F1 to hold 30 kg passively and puts the series through 20 stringent tests.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSix drives, twelve joints:\u003c\/strong\u003e Six degrees of freedom move twelve joints across five fingers, and fingertips repeat to ±0.2 mm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFast thumb and fingers:\u003c\/strong\u003e The thumb rotates laterally through 60–180° at over 155°\/s, the four fingers flex at over 107°\/s, and the hand closes in 0.8 s or less.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT and RS-485 at 1 kHz:\u003c\/strong\u003e The E2 build carries both interfaces with 1 kHz real-time communication on a 24–48 V supply.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Inspire Robots","offers":[{"title":"Default Title","offer_id":67633028956390,"sku":"Inspire-RH56F1-E2L","price":16700.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/inspire-robots-logo_4.jpg?v=1791277736"},{"product_id":"inspire-robots-inspire-dexterous-right-hand-with-tactile-sensors-rh56f1","title":"Inspire RH56F1 Tactile Dexterous Hand Right (E2R-T1)","description":"\u003cp\u003eThe Inspire RH56F1-E2R-T1 is the right-hand, tactile version of Inspire Robots' RH56F1 dexterous robotic hand: the same six-actuator, twelve-joint, all-metal hand as the RH56F1-E2R, with eight capacitive tactile sensors added in the fingertips and palm. It is the RH56F1 to choose when a robot has to feel where and how it touches an object, not only how hard each finger is pressing.\u003c\/p\u003e\u003cp\u003eEach of the five fingertips carries a sensor that reports normal force, tangential force and the direction of that tangential force from 0 to 359°, plus a proximity value as the finger approaches a surface. Three more sensors cover the left, middle and right zones of the palm and report normal and tangential force with direction. The range is 30 N and the accuracy 5 % of full scale, with readings delivered in 0.01 N steps; tangential force and its direction are the readings a controller uses to detect slip.\u003c\/p\u003e\u003cp\u003eThe mechanics match the rest of the RH56F1 line. Six micro linear servo actuators, each with a force sensor at 0.1 N resolution, move 12 joints; fingertips push with at least 15 N and the thumb with at least 10 N, and they repeat to ±0.2 mm. The thumb rotates laterally through 60–180°, the hand closes in 0.8 s or less, and Inspire rates the passive payload at 30 kg. It weighs 620 g and is 183.3 mm long and 79.1 mm across the palm.\u003c\/p\u003e\u003cp\u003eTactile values come from their own registers next to each actuator's position, force, current and temperature, over the E2 interface: EtherCAT, or RS-485 with Inspire's open protocol or Modbus RTU, with 1 kHz real-time communication on a 24–48 V supply. Each finger can run speed-force protection, force closed-loop or impedance control. The wrist mounts on four 3.5 mm through holes, and fitment to your arm or humanoid is confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eFor a two-handed robot, the \u003ca href=\"\/en\/products\/inspire-robots-inspire-dexterous-left-hand-with-tactile-sensors-rh56f1\"\u003eRH56F1 tactile left hand (E2L-T1)\u003c\/a\u003e is the mirror of this one. When finger force feedback is enough, the \u003ca href=\"\/en\/products\/inspire-robots-dexterous-right-hand-rh56f1\"\u003eRH56F1 right hand without tactile sensors (E2R)\u003c\/a\u003e has the same mechanics and interfaces. Compare the full range of \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eEight capacitive tactile sensors:\u003c\/strong\u003e One sensor in each fingertip and three across the palm measure contact up to 30 N with 5 % full-scale accuracy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eForce direction, not just pressure:\u003c\/strong\u003e Fingertip and palm sensors report normal force, tangential force and its direction from 0 to 359°, in 0.01 N steps.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProximity at the fingertips:\u003c\/strong\u003e Each fingertip sensor also returns a proximity value as the finger approaches a surface.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSix force-sensing actuators:\u003c\/strong\u003e Six micro linear servo actuators move 12 joints, and each reports finger force at 0.1 N resolution.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e620 g all-metal right hand:\u003c\/strong\u003e The hand is 183.3 mm long and 79.1 mm across the palm, pushes at least 15 N per fingertip and is rated for a 30 kg passive payload.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT and RS-485 at 1 kHz:\u003c\/strong\u003e The E2 interface combines both buses with 1 kHz real-time communication on a 24–48 V supply.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Inspire Robots","offers":[{"title":"Default Title","offer_id":67633029021926,"sku":"Inspire-RH56F1-E2R-T1","price":23400.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/inspire-robots-logo_4_1.jpg?v=1791277736"},{"product_id":"inspire-robots-inspire-dexterous-left-hand-with-tactile-sensors-rh56f1","title":"Inspire RH56F1 Tactile Dexterous Hand Left (E2L-T1)","description":"\u003cp\u003eThe Inspire RH56F1-E2L-T1 is the left hand in Inspire Robots' tactile RH56F1 dexterous robotic hand line. It combines the RH56F1's metal-framed, six-actuator design with eight capacitive tactile sensors, so the left hand of a humanoid or a research rig can tell where an object touches it, how hard it presses and in which direction it pulls.\u003c\/p\u003e\u003cp\u003eThat contact data is what grasp-learning work, teleoperation with touch feedback and the handling of fragile or deformable objects need, and force sensing in the actuators alone cannot give it. The five fingertip sensors return normal force, tangential force, force direction from 0 to 359° and proximity; three palm sensors, in left, middle and right zones, return normal and tangential force with direction. All eight cover a 30 N range at 5 % full-scale accuracy, read out in 0.01 N steps.\u003c\/p\u003e\u003cp\u003eUnderneath is the full RH56F1: 12 joints moved by 6 degrees of freedom, a force sensor on each of the six actuators at 0.1 N resolution, at least 15 N at each fingertip and 10 N at the thumb, ±0.2 mm repeatability and a 30 kg passive payload as Inspire rates it. It weighs 620 g, is 183.3 mm long and 79.1 mm across the palm, and closes fully in 0.8 s or less while the thumb rotates through 60–180°.\u003c\/p\u003e\u003cp\u003eThe E2 interface puts EtherCAT and RS-485 side by side with 1 kHz real-time communication, on a 24–48 V supply that peaks at 5 A at 24 V. Tactile readings sit in their own registers next to joint position, force, current and actuator temperature, and each finger can run speed-force protection, force closed-loop or impedance control. Mounting to your arm or humanoid is confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eFor a two-handed robot, the \u003ca href=\"\/en\/products\/inspire-robots-inspire-dexterous-right-hand-with-tactile-sensors-rh56f1\"\u003eRH56F1 tactile right hand (E2R-T1)\u003c\/a\u003e mirrors this one. The \u003ca href=\"\/en\/products\/inspire-robots-inspire-dexterous-left-hand-rh56f1\"\u003eRH56F1 left hand without tactile sensors (E2L)\u003c\/a\u003e shares the mechanics and is the choice when finger force feedback is enough. Browse all of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eContact sensing in fingers and palm:\u003c\/strong\u003e Eight capacitive sensors, five at the fingertips and three in the palm, read contact up to 30 N at 5 % full-scale accuracy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTangential force and direction:\u003c\/strong\u003e Each reading includes tangential force and its direction from 0 to 359° alongside normal force, in 0.01 N steps.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProximity in every fingertip:\u003c\/strong\u003e The five fingertip sensors add a proximity reading as a finger approaches a surface.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRH56F1 mechanics:\u003c\/strong\u003e Six degrees of freedom move 12 joints, with at least 15 N per fingertip, ±0.2 mm repeatability and a 30 kg passive payload rating.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e620 g metal skeleton:\u003c\/strong\u003e An all-metal integrated frame with concealed wiring, 183.3 mm long and 79.1 mm across the palm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree control modes per finger:\u003c\/strong\u003e Speed-force protection, force closed-loop and impedance control run over EtherCAT or RS-485 with 1 kHz real-time communication.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Inspire Robots","offers":[{"title":"Default Title","offer_id":67633029284070,"sku":"Inspire-RH56F1-E2L-T1","price":23400.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/inspire-robots-logo_2.jpg?v=1791277737"},{"product_id":"robotera-xhand1","title":"Robotera XHAND1 Lite Dexterous Hand","description":"\u003cp\u003eThe Robotera XHAND1 Lite, which Robotera calls its “Agile Elf Hand”, is a slim five-finger dexterous robotic hand of human-hand size, built for speed and for slim humanoid and service robots. It weighs 730 g and measures 209 × 84 × 32 mm, against 1,100 g and 47 mm thickness for the full XHAND1, and Robotera fits it to its own Q5 wheeled humanoid.\u003c\/p\u003e\u003cp\u003eIt has 11 degrees of freedom, 6 active and 5 passive. The thumb has two driven joints plus a passive one, and each of the four fingers one driven joint plus a passive one, coupled through linkages and micro force-controlled composite joints. The thumb still reaches the little finger in opposition, and the joints are backdrivable, which Robotera ties to fault-tolerant data collection and a higher inference success rate.\u003c\/p\u003e\u003cp\u003eSpeed is its strength: fast response up to 10 clicks per second and an open-close rate above 2 Hz, for gestures and interactive tasks. Each fingertip carries 12 N, the hand grasps objects from 12 mm across, Robotera rates the single-hand payload at 10 kg, and fingertips repeat to ±0.20 mm. It is rated for one million no-load grasp cycles.\u003c\/p\u003e\u003cp\u003eControl runs over EtherCAT at 100 Mbps or RS-485 at 3 Mbps via USB, in position mode with low or high damping, or in current-loop force control. Hand side, tactile options and operating voltage are confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eFor research that needs every joint driven, the full XHAND1, sold as a \u003ca href=\"\/en\/products\/robotera-right-xhand1\"\u003eright hand\u003c\/a\u003e and a \u003ca href=\"\/en\/products\/robotera-left-xhand1\"\u003eleft hand\u003c\/a\u003e, has 12 active degrees of freedom, 270° tactile fingertips and up to 80 N of grip. Compare the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e730 g and 32 mm thin:\u003c\/strong\u003e At 209 × 84 × 32 mm and 730 g, it suits slim humanoid and service-robot arms.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e11 DoF, 6 of them driven:\u003c\/strong\u003e Two driven thumb joints and one in each finger, plus five passive joints coupled through linkages.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp to 10 clicks per second:\u003c\/strong\u003e Fast response and an open-close rate above 2 Hz suit gestures and interactive tasks.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e10 kg single-hand payload:\u003c\/strong\u003e Robotera rates the hand at 10 kg, with 12 N per fingertip and grasps from 12 mm diameter.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBackdrivable joints:\u003c\/strong\u003e The joints back-drive under load, and the thumb opposes every finger down to the little finger.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT or RS-485:\u003c\/strong\u003e EtherCAT at 100 Mbps or RS-485 at 3 Mbps, with position and current-loop force control.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"RobotEra","offers":[{"title":"Default Title","offer_id":67633029939430,"sku":"RobotEra-XHAND1-Lite","price":62250.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/elfin_2_8a84eb5e-5ce8-417d-b871-a2ba6c6af9f7.png?v=1791277737"},{"product_id":"unitree-robotics-dex5","title":"Unitree Dex5-1P Tactile Dexterous Hand Left for H1\/H1-2","description":"\u003cp\u003eThe Unitree Dex5-1P is Unitree's five-finger tactile dexterous robotic hand, and this is the left hand built for the H1 and H1-2 humanoids (part DEX5-HANDL). Unitree offers the Dex5-1 as an optional hand for the H1-2; the P marks the build with 94 pressure sensors in the palm, finger pads, fingertips and finger roots. It is meant for H1 and H1-2 owners doing manipulation research or reinforcement and imitation learning, and Unitree opens the hand to secondary development for teams writing their own tactile algorithms.\u003c\/p\u003e\u003cp\u003eThe hand has 20 degrees of freedom, 16 of them active: four in the thumb and three in each finger, with ±22° of lateral swing across the four fingers. Twelve joints use Unitree's micro force-controlled composite transmission, which gives the hand tactile proprioception, and four use force-controlled gear transmissions, driven by hollow-cup motors with high-precision encoders. Every finger joint is backdrivable, which Unitree designed to end the \"stiff hand\" problem in reinforcement-learning training, and each of the five fingers can be replaced on its own.\u003c\/p\u003e\u003cp\u003eFingertip strength is 10 N, fingertip repeatability ±1 mm, and the fingers close on objects down to 10 mm across. Holding a 5 cm round hard object, the hand carries up to 3.5 kg palm down and 4.5 kg with the palm facing left. Its pressure arrays (2 × 5 in the palm, 2 × 3 on each finger pad, fingertip and four finger roots) sense from 10 g to 2,500 g and take 20 kg without damage. Pressure and sensor temperature arrive in the same 1,000 Hz USB 2.0 stream as joint position, velocity, torque, temperature, voltage, current and IMU data. It weighs 1,100 g, measures 217.3 × 127.5 × 72.1 mm laid flat and runs on 24–60 V.\u003c\/p\u003e\u003cp\u003eWithin the Dex5 family, the \u003ca href=\"\/en\/products\/unitree-dex5-1-five-finger-dexterous-hand\"\u003eUnitree Dex5-1\u003c\/a\u003e is the same hand without the pressure sensors, and the \u003ca href=\"\/en\/products\/unitree-dex5-1p-tactile-five-finger-hand\"\u003eDex5-1P for the Unitree H2\u003c\/a\u003e is listed separately. The \u003ca href=\"\/en\/products\/unitree-dex5-s-22-dof-dexterous-hand\"\u003eUnitree Dex5-S\u003c\/a\u003e is a different design: 22 degrees of freedom, all motor-driven, at 620 g and 1:1 human-hand scale. For a two-handed H1 or H1-2, ask us for the matching right hand, or compare the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e94 pressure sensors:\u003c\/strong\u003e Arrays in the palm, on every finger pad and fingertip and at four finger roots sense from 10 g to 2,500 g and take 20 kg without damage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e20 degrees of freedom, 16 active:\u003c\/strong\u003e The thumb has four driven joints and each finger three, with ±22° of lateral swing across the four fingers.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBackdrivable joints, replaceable fingers:\u003c\/strong\u003e Every finger joint can be back-driven, which keeps reinforcement-learning training smooth, and each of the five fingers can be swapped on its own.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp to 4.5 kg grasp load:\u003c\/strong\u003e Holding a 5 cm round object it carries 3.5 kg palm down and 4.5 kg palm facing left, with 10 N at each fingertip.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1,000 Hz over USB 2.0:\u003c\/strong\u003e Joint, pressure, temperature and IMU data stream at 1,000 Hz, and each joint takes position, velocity, torque, stiffness and damping commands.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuilt for the H1 and H1-2:\u003c\/strong\u003e This left hand is the Dex5-1P build for Unitree's H1 and H1-2 humanoids and runs on 24–60 V.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Unitree Robotics","offers":[{"title":"Default Title","offer_id":67633049469158,"sku":"Unitree-DEX5-HANDL","price":107250.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/unitree-dex5-1p-tactile-hand-for-unitree-h1-h1-2-left-img1.jpg?v=1791277751"},{"product_id":"unitree-robotics-g1-dex3-1-three-finger-dexterous-hand","title":"Unitree Dex3-1 Three-Finger Dexterous Hand for G1","description":"\u003cp\u003eThe Unitree Dex3-1 is Unitree's force-controlled three-finger dexterous robotic hand for the G1 humanoid, and this is the G1 accessory without tactile arrays, part G1-DEX3-3FINGERHAND. Unitree offers it as the three-finger hand of the G1 EDU, and its three opposed digits cover pinches, wraps and tool grasps with fewer joints to control than a five-finger hand.\u003c\/p\u003e\u003cp\u003eSeven degrees of freedom are split three in the thumb and two each in the index and middle finger. Six joints are direct-drive micro brushless force-control units built on Unitree's 45 g F-1515 joint motors, and one is gear-driven, so hybrid force and position control happens at the joints themselves. Every joint takes position, velocity, torque, stiffness and damping commands and reports its state at 1,000 Hz over USB 2.0.\u003c\/p\u003e\u003cp\u003eThe hand weighs 710 g, measures 175 × 88 × 77 mm flat and repeats fingertip position to ±2 mm. It holds up to 500 g on a 5 cm round hard object, palm down or palm left, with 400 W of peak power for 3 s, runs on 12–58 V and works from −20 to 60 °C. Without tactile arrays it suits teleoperation, grasp research and teaching, where joint force and position feedback are enough.\u003c\/p\u003e\u003cp\u003eFor touch data, the \u003ca href=\"\/en\/products\/unitree-robotics-g1-dex3-1-tactile-three-finger-hand\"\u003eDex3-1 Tactile for the G1\u003c\/a\u003e adds 33 pressure sensors on the same mechanism. The \u003ca href=\"\/en\/products\/unitree-dex3-1-three-finger-dexterous-hand\"\u003eDex3-1 for the Unitree H2\u003c\/a\u003e is a separate part for that robot. Five-finger options for the G1 are the \u003ca href=\"\/en\/products\/unitree-robotics-g1-third\"\u003eG1 Third-Party Dexterous Hand\u003c\/a\u003e and the \u003ca href=\"\/en\/products\/unitree-tendon-driven-dexterous-hand\"\u003eUnitree Dex2\/5\u003c\/a\u003e; see all of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eForce control at the joint:\u003c\/strong\u003e Six joints are direct-drive micro brushless force-control units and one is gear-driven, so grip force is set at the finger joints.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree fingers, 7 degrees of freedom:\u003c\/strong\u003e The thumb carries three degrees of freedom and the index and middle fingers two each, with 0–100° of bend at the outer joints.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMade for the Unitree G1:\u003c\/strong\u003e Unitree offers the Dex3-1 as the G1 EDU's three-finger hand; this is the version without tactile arrays, part G1-DEX3-3FINGERHAND.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1,000 Hz over USB 2.0:\u003c\/strong\u003e Joint position, velocity, torque, temperature, voltage and current come back 1,000 times a second, and commands set stiffness and damping per joint.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompact at 710 g:\u003c\/strong\u003e The hand measures 175 × 88 × 77 mm flat and repeats fingertip position to ±2 mm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRated grasp of 500 g:\u003c\/strong\u003e It holds up to 500 g on a 5 cm round hard object, palm down or palm left, with 400 W of peak power for 3 s.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Unitree Robotics","offers":[{"title":"Default Title","offer_id":67633050353894,"sku":"Unitree-G1-DEX3-3FINGERHAND","price":24200.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/unitree_g1_dex3-1_force_control_three_finger_dexterity_hand_1_1.jpg?v=1791277753"},{"product_id":"unitree-robotics-g1-dex3-1-tactile-three-finger-hand","title":"Unitree Dex3-1 Tactile Three-Finger Hand for G1","description":"\u003cp\u003eThe Unitree Dex3-1 Tactile is Unitree's three-finger dexterous robotic hand for the G1 humanoid in its tactile version, part G1-DEX3-3FINGERHAND-TACTILE. On the same seven-degree-of-freedom, force-controlled mechanism as the standard Dex3-1, it carries 33 pressure sensors in 9 arrays across the palm, the finger pads and the fingertips.\u003c\/p\u003e\u003cp\u003eWith pressure at the contact points, a G1 can tell when a finger touches, how hard each pad presses and how the load shifts during a grasp, rather than guessing contact from joint torque. The sensors cover 10 g to 2,500 g and report pressure and their own temperature in the same 1,000 Hz USB 2.0 stream as joint position, velocity, torque, voltage, current and IMU data. That suits teleoperation with touch feedback, tactile datasets for imitation learning and work with light or fragile objects.\u003c\/p\u003e\u003cp\u003eThe thumb has three degrees of freedom and the index and middle fingers two each. Six joints are direct-drive micro brushless force-control units and one is gear-driven, giving hybrid force and position control at the joints. The hand weighs 710 g, measures 175 × 88 × 77 mm flat, repeats fingertip position to ±2 mm and grasps up to 500 g on a 5 cm round hard object, with 400 W of peak power for 3 s; the sensors take 20 kg without damage. It runs on 12–58 V and from −20 to 60 °C.\u003c\/p\u003e\u003cp\u003eThe \u003ca href=\"\/en\/products\/unitree-robotics-g1-dex3-1-three-finger-dexterous-hand\"\u003estandard Dex3-1 for the G1\u003c\/a\u003e is the same hand without the tactile arrays, and the \u003ca href=\"\/en\/products\/unitree-dex3-1-tactile-three-finger-hand\"\u003eDex3-1 Tactile for the Unitree H2\u003c\/a\u003e is sold as its own part, so order the one that matches your robot. For five fingers on a G1, see the \u003ca href=\"\/en\/products\/unitree-robotics-g1-third\"\u003eG1 Third-Party Dexterous Hand\u003c\/a\u003e or the tendon-driven \u003ca href=\"\/en\/products\/unitree-tendon-driven-dexterous-hand\"\u003eUnitree Dex2\/5\u003c\/a\u003e, and compare our other \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e33 pressure sensors in 9 arrays:\u003c\/strong\u003e Three 2 × 2 arrays in the palm, a 2 × 2 array on each finger pad and a 3 × 1 array at each fingertip sense from 10 g to 2,500 g.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTouch in the joint stream:\u003c\/strong\u003e Pressure and sensor temperature arrive at 1,000 Hz over USB 2.0 together with joint position, velocity, torque and IMU data.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHybrid force and position control:\u003c\/strong\u003e Six direct-drive micro brushless force-control joints and one geared joint set grip force at the fingers themselves.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree fingers, 7 degrees of freedom:\u003c\/strong\u003e The thumb has three degrees of freedom and swings from −60° to 60° at its base; the index and middle fingers have two each.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMade for the G1:\u003c\/strong\u003e Unitree builds the Dex3-1 for its G1 humanoid, and this is the tactile version, part G1-DEX3-3FINGERHAND-TACTILE.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e710 g, 500 g grasp:\u003c\/strong\u003e The hand measures 175 × 88 × 77 mm flat, grasps up to 500 g, and its sensors take 20 kg without damage.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Unitree Robotics","offers":[{"title":"Default Title","offer_id":67633050419430,"sku":"Unitree-G1-DEX3-TACTILE-HAND","price":28990.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/unitree_g1_dex3-1_force_control_three_finger_dexterity_hand_1.jpg?v=1791277752"},{"product_id":"unitree-robotics-g1-third","title":"Unitree G1 Third-Party Dexterous Hand (One-Handed)","description":"\u003cp\u003eThe Unitree G1 Third-Party Dexterous Hand is a five-finger dexterous robotic hand that Unitree supplies for the G1 humanoid under part G1-DEX-RH-LH, sold as one hand for the left or the right side. It replaces the G1's three-finger hand on one arm with a full set of fingers and a thumb that opposes them.\u003c\/p\u003e\u003cp\u003eSix degrees of freedom drive twelve joints across the five fingers, with ±0.20 mm repeat positioning accuracy. That suits embodied-AI and manipulation research on the G1 where the task calls for five-finger grasps on tools, handles, bottles and test parts, and where repeatable finger positions matter more than heavy payloads.\u003c\/p\u003e\u003cp\u003eBecause each unit is a single hand, a team can fit one dexterous hand and keep a simpler hand on the other arm, or add the second side later. The two sides are mirror images in thumb opposition, finger kinematics and mounting, so the side is chosen when ordering. The hand model, grip force, weight, interface and fitting to your G1 are confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eUnitree's own hands for the G1 are the three-finger \u003ca href=\"\/en\/products\/unitree-robotics-g1-dex3-1-three-finger-dexterous-hand\"\u003eDex3-1\u003c\/a\u003e and \u003ca href=\"\/en\/products\/unitree-robotics-g1-dex3-1-tactile-three-finger-hand\"\u003eDex3-1 Tactile\u003c\/a\u003e, with 7 force-controlled degrees of freedom, and the light, tendon-driven \u003ca href=\"\/en\/products\/unitree-tendon-driven-dexterous-hand\"\u003eDex2\/5\u003c\/a\u003e five-finger hand. Compare them with our other \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFive fingers on a G1:\u003c\/strong\u003e The hand gives a G1 five fingers in place of a three-finger hand, for grasps that need a full thumb opposition.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e6 degrees of freedom, 12 joints:\u003c\/strong\u003e Six drives move twelve finger joints across the five fingers, with linked joints in each finger.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e±0.20 mm repeatability:\u003c\/strong\u003e Repeat positioning accuracy of ±0.20 mm keeps grasps consistent from one trial to the next.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne hand per unit:\u003c\/strong\u003e Each unit is a single hand, so a G1 can carry one five-finger hand and one simpler hand, or two of these.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLeft or right, chosen at order:\u003c\/strong\u003e Thumb opposition and mounting are mirrored between sides, so the side is set when you order.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart G1-DEX-RH-LH:\u003c\/strong\u003e Unitree supplies the hand as a G1 accessory under this part number.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Unitree Robotics","offers":[{"title":"Default Title","offer_id":67633050648806,"sku":"Unitree-G1-DEX-RH-LH","price":28990.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/unitree_g1_third-party_dexterity_one-handed_g1-dex-rh-lh.jpg?v=1791277752"},{"product_id":"unitree-robotics-h1-2-dexterous-hand","title":"Unitree H1-2 Dexterous Hand","description":"\u003cp\u003eThe Unitree H1-2 Dexterous Hand is a five-finger dexterous robotic hand that Unitree develops for its H1-2 full-size humanoid. It mounts at the end of the H1-2's arms, each with seven degrees of freedom including a three-axis wrist, and gives the robot a hand for grasping and manipulation instead of a bare wrist.\u003c\/p\u003e\u003cp\u003eIt is for H1-2 owners and research labs working on manipulation, teleoperation and imitation learning, where demonstrations are recorded through the robot's own hands and replayed as learned policies. Pairing the hand with the H1-2's three-axis wrist lets the robot orient the palm to an object before the fingers close.\u003c\/p\u003e\u003cp\u003eThe hand's degrees of freedom, weight, grip force, sensors and control interface, the side or pair you need and the mounting to your H1-2 are confirmed with the quotation, so the configuration matches the robot you already run.\u003c\/p\u003e\u003cp\u003eFor a tactile hand on the H1 or H1-2, Unitree's \u003ca href=\"\/en\/products\/unitree-robotics-dex5\"\u003eDex5-1P Tactile Dexterous Hand Left for H1\/H1-2\u003c\/a\u003e carries 94 pressure sensors and 20 degrees of freedom. Compare it, and the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e, before you choose.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMade by Unitree for the H1-2:\u003c\/strong\u003e Unitree develops this hand for its H1-2 full-size humanoid, so it is specified for that robot's arms.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits a 7-DoF arm:\u003c\/strong\u003e Each H1-2 arm has seven degrees of freedom, three of them in the wrist, which lets the hand reach and orient for a grasp.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFive-finger end effector:\u003c\/strong\u003e The hand gives the H1-2 a five-finger grasp in place of a bare wrist or a simple gripper.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFor teleoperation and learning:\u003c\/strong\u003e H1-2 teams use dexterous hands for teleoperated demonstrations and imitation-learning datasets.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpecification agreed per order:\u003c\/strong\u003e Hand side, quantity, weight, force and interface for your H1-2 are confirmed with the quotation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Unitree Robotics","offers":[{"title":"Default Title","offer_id":67633051468006,"sku":"Unitree-H1-2-Dexterous-Hand","price":36990.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/unitree_g1_third-party_dexterity_one-handed_g1-dex-rh-lh__1.jpg?v=1791277753"},{"product_id":"agibot-omnihand-pro-2025-five-finger-dexterous-hand","title":"AgiBot OmniHand Pro 2025 Dexterous Hand","description":"\u003cp\u003eThe AgiBot OmniHand Pro 2025 is the high-end dexterous robotic hand of AgiBot's OmniHand 2025 range, built around force sensing in every fingertip. Its five fingers have 19 degrees of freedom, 12 of them driven by their own motors through a linkage and screw-rod transmission, inside a PA and silicone body that measures 207 × 98 × 56 mm and weighs no more than 750 g. AgiBot builds it as a left and a right hand, so state the side, or a pair, with your order.\u003c\/p\u003e\u003cp\u003eWhat sets the Pro apart is what it feels. Each fingertip measures force in three axes and the palm in one, across more than 150 tactile points with 0.01 N resolution and a 0–50 N range, and the sensors withstand 1,000 N without damage. A tactile control mode joins speed, position, force and hybrid position-force control, so a grasp can be set by contact rather than by joint angle alone. That makes it a fit for manipulation and grasp-learning research, teleoperation, and humanoids or arms that handle fragile, small or mixed objects.\u003c\/p\u003e\u003cp\u003eIt is also strong for its size: up to 20 N at each fingertip, and holding a 5 cm rigid object it carries 35 kg palm up and 5 kg palm down. Fingers reposition to 0.02 mm, close on objects from 2 mm across and close fully in 0.8 s. Control and data run over CAN FD at 1 kHz on a 12–24 V supply, and AgiBot's SDK gives C++ and Python APIs, a kinematics library and a ROS 2 interface on Linux, with Windows host software for setup. The CAN FD and power cables come in the box.\u003c\/p\u003e\u003cp\u003eWithin the OmniHand family, the \u003ca href=\"\/en\/products\/agibot-omnihand-2025-tactile-right-robot-hand\"\u003eOmniHand 2025 Tactile right hand\u003c\/a\u003e is the lighter interactive model, with 16 degrees of freedom (10 active), one-axis touch sensing that also covers the back of the hand, and RS-485 alongside CAN FD. The \u003ca href=\"\/en\/products\/agibot-omnihand-3-ultra-m-flagship-direct-driven-dexterous-robot-hand\"\u003eOmniHand 3 Ultra-M\u003c\/a\u003e is AgiBot's direct-drive flagship with 21 active degrees of freedom and vision-based tactile fingertips. Compare them with the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e3-axis force in every fingertip:\u003c\/strong\u003e Each fingertip senses force in three axes and the palm in one, with more than 150 tactile points read at 0.01 N resolution across a 0–50 N range.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e19 degrees of freedom, 12 driven:\u003c\/strong\u003e Twelve motors move 19 joints through a linkage and screw-rod drive, so the four fingers spread ±10° and the thumb rotates 50° as well as flexing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e20 N at the fingertip:\u003c\/strong\u003e Fingertips push with up to 20 N, and holding a 5 cm rigid object the hand carries 35 kg palm up and 5 kg palm down.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.02 mm repositioning:\u003c\/strong\u003e Fingers return to position within 0.02 mm and close on objects as small as 2 mm, which suits precise pinches and small parts.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFive control modes:\u003c\/strong\u003e Speed, position, force, hybrid position-force and tactile modes run over CAN FD at 1 kHz, with joint position, speed, torque, temperature, current and tactile pressure fed back.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eC++, Python and ROS 2:\u003c\/strong\u003e AgiBot's SDK offers C++ and Python APIs with a kinematics library and a ROS 2 interface on Linux, and it runs on Windows as well.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"AGIBOT","offers":[{"title":"Default Title","offer_id":67633060774118,"sku":"AgiBot-OmniHand-Pro-2025","price":12250.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/agibot-omnihand-pro-2025.jpg?v=1791277762"},{"product_id":"inspire-rh56e2-dexterous-robot-hand","title":"Inspire RH56E2 Heavy-Load Dexterous Hand","description":"\u003cp\u003eThe Inspire RH56E2 is the heavy-load dexterous robotic hand from Inspire Robots' RH56 series: five fingers and six actuators built to grip with the force of a human hand. Inspire describes it as the first industrial-grade dexterous hand with human-hand grasping force, with 30 N at the thumb tip, 28 N at each fingertip and an overall load capacity equivalent to 15 kg.\u003c\/p\u003e\u003cp\u003eThat strength is the reason to choose it over lighter hands: power tools, door handles, kettlebells, boxes and workpieces in industrial automation, service robots and teaching labs. A power-off self-lock holds the fingers in place when power is cut.\u003c\/p\u003e\u003cp\u003eSix micro linear servo actuators move 12 joints, each with a force sensor that reads finger force at 0.05 N resolution, and fingertips repeat to ±0.20 mm. The thumb rotates laterally through 75–170° at more than 130°\/s and flexes at more than 130°\/s, the four fingers flex at more than 200°\/s, and the hand closes in 0.8 s. It measures 211.5 mm long, 93.0 mm across the palm and 47.5 mm thick, and runs on 24 V ±10 % with a 4 A peak.\u003c\/p\u003e\u003cp\u003eThe RH56E2 comes as a left or a right hand, each with Modbus TCP over Ethernet plus either CAN 2.0 (the -0 models) or RS-485 (the -2 models). Without tactile sensors it weighs 770 ± 10 g. The T1 tactile build adds 17 piezoresistive sensors across the fingertips, finger pads and palm with a 0–30 N range; the T2 build carries five capacitive sensors with a 0–20 N range; both are accurate to 5 % of full scale and weigh 790 ± 10 g. Hand side, bus and tactile option are confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eFor lighter work, the \u003ca href=\"\/en\/products\/inspire-rh56dfx-dexterous-robot-hand\"\u003eInspire RH56DFX\u003c\/a\u003e weighs 540 g with 15 N at the thumb tip, and the \u003ca href=\"\/en\/products\/inspire-robots-inspire-dexterous-left-hand-rh56f1\"\u003eInspire RH56F1\u003c\/a\u003e brings EtherCAT at 620 g. Compare them with the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e30 N thumb, 28 N fingertips:\u003c\/strong\u003e The thumb tip pushes with 30 N and each fingertip with 28 N, and Inspire rates the overall load capacity at the equivalent of 15 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHolds its grip with power off:\u003c\/strong\u003e A power-off self-lock keeps every finger in place when the supply is cut.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eForce sensing at 0.05 N:\u003c\/strong\u003e Six force sensors, one per actuator, read finger force at 0.05 N resolution for threshold-based or closed-loop gripping.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTactile builds with 17 or 5 sensors:\u003c\/strong\u003e The T1 build carries 17 piezoresistive sensors over fingertips, finger pads and palm (0–30 N); the T2 build carries five capacitive sensors (0–20 N).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eModbus TCP plus CAN or RS-485:\u003c\/strong\u003e Every RH56E2 connects over Modbus TCP on Ethernet, plus CAN 2.0 or RS-485 depending on the model.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuick, repeatable fingers:\u003c\/strong\u003e The four fingers flex at over 200°\/s, the hand closes in 0.8 s, and fingertips repeat to ±0.20 mm.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Inspire Robots","offers":[{"title":"Default Title","offer_id":67633061331174,"sku":"Inspire-RH56E2","price":27900.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/inspire-robots-rh56e2.jpg?v=1791277762"},{"product_id":"agibot-omnihand-2025-tactile-right-robot-hand","title":"AgiBot OmniHand 2025 Tactile Dexterous Hand Right","description":"\u003cp\u003eThe AgiBot OmniHand 2025 Tactile is the touch-sensing build of AgiBot's compact OmniHand 2025 dexterous robotic hand, and this is the right hand. Force-sensing arrays cover all five fingers, the palm and the back of the hand, adding contact data to 16 degrees of freedom (10 driven) in a 180 mm hand that weighs no more than 550 g.\u003c\/p\u003e\u003cp\u003eThe sensing is what separates it from the standard OmniHand 2025. More than 300 force-sensing taxels sit in seven regions — the thumb, four fingers, palm and back of the hand — each reading one-axis force from 0 to 20 N at 0.1 N resolution and tolerating 200 N without damage. The arrays on the back of the hand give the back-of-hand touch interaction AgiBot highlights for this hand. A tactile control mode and tactile pressure feedback join the position, torque, hybrid and velocity modes, so research teams can record contact during grasping, teleoperation and human-robot interaction.\u003c\/p\u003e\u003cp\u003eMechanically it matches the standard hand: a thumb with three driven joints, two each in the index, ring and little fingers and one in the middle finger, 0.3 mm fingertip repeatability, 0.5 s to open or close, up to 5 N per fingertip and at least 5 kg of five-finger grip in hybrid force control. It connects over CAN FD or RS-485 at 1 kHz, or USB Type-C to a host computer, on 24 V, and AgiBot's SDK (C++, Python, ROS 2) reads the tactile arrays alongside the joints.\u003c\/p\u003e\u003cp\u003eThe \u003ca href=\"\/en\/products\/agibot-omnihand-2025-tactile-left-robot-hand\"\u003eOmniHand 2025 Tactile left hand\u003c\/a\u003e completes a sensing pair, and the \u003ca href=\"\/en\/products\/agibot-omnihand-2025-dexterous-right-robot-hand\"\u003estandard OmniHand 2025 right hand\u003c\/a\u003e is the same hand without the arrays. For three-axis fingertip force at 0.01 N, see the \u003ca href=\"\/en\/products\/agibot-omnihand-pro-2025-five-finger-dexterous-hand\"\u003eOmniHand Pro 2025\u003c\/a\u003e, or browse all our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTouch on fingers, palm and back:\u003c\/strong\u003e More than 300 force-sensing taxels in seven regions read one-axis force from 0 to 20 N at 0.1 N resolution.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBack-of-hand touch interaction:\u003c\/strong\u003e Arrays on the back of the hand let the robot respond when a person touches it there, alongside the usual gestures.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTactile control mode:\u003c\/strong\u003e A tactile mode and tactile pressure feedback sit beside position, torque, hybrid position-torque and velocity control.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e16 degrees of freedom at up to 550 g:\u003c\/strong\u003e Ten driven and six passive joints sit in a 180 × 85 × 38.5 mm PA and silicone body.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e5 kg grip, 0.3 mm repeatability:\u003c\/strong\u003e The five-finger grip reaches at least 5 kg in hybrid force control, fingertips repeat to 0.3 mm and the hand closes in 0.5 s.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCAN FD, RS-485 and USB:\u003c\/strong\u003e Communication runs at 1 kHz on 24 V, with a C++, Python and ROS 2 SDK and over-the-air firmware updates.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"AGIBOT","offers":[{"title":"Default Title","offer_id":67633061495014,"sku":"AgiBot-OmniHand-2025-Tactile","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/agibot-omnihand-2025-w-tactile-1.jpg?v=1791277763"},{"product_id":"agibot-omnihand-3-lite-ruggedized-dexterous-hand","title":"AgiBot OmniHand 3 Lite Dexterous Hand","description":"\u003cp\u003eThe AgiBot OmniHand 3 Lite is the smallest hand in AgiBot's OmniHand 3 series: a five-finger dexterous robotic hand of 350 g that measures 140 × 70 × 32 mm, about the size of a computer mouse. AgiBot built it to bring five-finger manipulation to half-scale humanoids, mobile manipulators and compact service robots, platforms that otherwise end up with a gripper.\u003c\/p\u003e\u003cp\u003eIts design favours durability. An aerospace-grade metal frame carries a one-piece silicone overmold, and AgiBot validated the hand through impact, drop and collision testing, rating it to stay on the robot through dynamic motion, including cartwheels and acrobatics that usually mean taking the hands off. Four driven joints and seven passive ones give 11 degrees of freedom, enough for the five fingers to wrap around objects, with up to 7.5 N at each fingertip, ±0.5 mm repeatability and a 0.5 s opening or closing time.\u003c\/p\u003e\u003cp\u003eSix one-axis tactile sensors, one in each finger and one in the palm, report contact alongside the joint data over CAN FD or RS-485. An optional wrist-mounted camera, compatibility with Dex-UMI data-collection systems and AgiBot's open-source toolkit, with C++ and Python APIs and a ROS 2 interface, suit it to rapid prototyping, classroom robotics and developer programmes as well as light industrial handling.\u003c\/p\u003e\u003cp\u003eWithin the family, the \u003ca href=\"\/en\/products\/agibot-omnihand-2025-dexterous-right-robot-hand\"\u003eOmniHand 2025\u003c\/a\u003e is the full-size interactive hand with 16 degrees of freedom, and the \u003ca href=\"\/en\/products\/agibot-omnihand-3-ultra-m-flagship-direct-driven-dexterous-robot-hand\"\u003eOmniHand 3 Ultra-M\u003c\/a\u003e is the 21-DoF direct-drive flagship for research. AgiBot makes the Lite as a left and a right hand; name the side with your order, and compare it with our other \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e350 g and mouse-sized:\u003c\/strong\u003e At 140 × 70 × 32 mm and 350 g, it fits half-scale humanoids, mobile manipulators and compact service robots.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMetal frame, silicone overmold:\u003c\/strong\u003e An aerospace-grade metal frame sits under a one-piece silicone overmold, validated through impact, drop and collision testing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e11 degrees of freedom from 4 motors:\u003c\/strong\u003e Four driven and seven passive joints let the fingers wrap around objects, with ±0.5 mm repeatability.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e7.5 N fingertips:\u003c\/strong\u003e Each fingertip pushes with up to 7.5 N, and the hand opens or closes in 0.5 s.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTouch in fingers and palm:\u003c\/strong\u003e Six one-axis tactile sensors, one in each finger and one in the palm, report contact with the joint data.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOpen developer toolkit:\u003c\/strong\u003e The hand connects over CAN FD or RS-485, takes an optional wrist camera, works with Dex-UMI data collection and comes with AgiBot's open-source C++, Python and ROS 2 toolkit.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"AGIBOT","offers":[{"title":"Default Title","offer_id":67633061593318,"sku":"AgiBot-OmniHand-3-Lite","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/agibot-omnihand-2025-w-tactile-1_2.jpg?v=1791277762"},{"product_id":"agibot-omnihand-2025-tactile-left-robot-hand","title":"AgiBot OmniHand 2025 Tactile Dexterous Hand Left","description":"\u003cp\u003eThis is the left hand of the AgiBot OmniHand 2025 Tactile, the version of AgiBot's compact dexterous robotic hand that feels what it touches. Mounted on the left wrist of a humanoid or robot arm, and paired with the matching right hand, it gives a two-handed robot touch sensing on both sides: force-sensing arrays on the fingers, palm and back of the hand, 16 degrees of freedom and no more than 550 g per hand.\u003c\/p\u003e\u003cp\u003eWhere the standard OmniHand 2025 knows only its joint positions and torques, this hand also reports where and how hard it is touched. More than 300 taxels in seven regions read one-axis force across 0–20 N at 0.1 N resolution and withstand 200 N, and the data arrives with the joint feedback over CAN FD or RS-485 at 1 kHz. That suits bimanual grasping studies, teleoperation, learning data that includes contact, and robots that respond to a touch on the back of the hand.\u003c\/p\u003e\u003cp\u003eTen of its 16 joints are driven: three in the thumb, two in each of the index, ring and little fingers and one in the middle finger, with six passive joints following. Fingertips push with up to 5 N and repeat to 0.3 mm, the five-finger grip reaches at least 5 kg in hybrid force control, and the hand opens or closes in 0.5 s. It runs on 24 V, measures 180 × 85 × 38.5 mm, mounts with four M4 screws and comes with power, CAN FD, RS-485 and USB Type-C cables. AgiBot's C++, Python and ROS 2 SDK and its URDF and MuJoCo models support development and simulation.\u003c\/p\u003e\u003cp\u003eOrder it with the \u003ca href=\"\/en\/products\/agibot-omnihand-2025-tactile-right-robot-hand\"\u003eOmniHand 2025 Tactile right hand\u003c\/a\u003e for a sensing pair. Without the arrays, the \u003ca href=\"\/en\/products\/agibot-omnihand-2025-dexterous-left-robot-hand\"\u003estandard OmniHand 2025 left hand\u003c\/a\u003e covers gesture and light handling, and the \u003ca href=\"\/en\/products\/agibot-omnihand-3-lite-ruggedized-dexterous-hand\"\u003eOmniHand 3 Lite\u003c\/a\u003e is AgiBot's 350 g hand for smaller robots. See every option in our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eContact data on both sides of the hand:\u003c\/strong\u003e Force-sensing arrays on the palm and the back of the hand, as well as all five fingers, report where and how hard the hand is touched.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.1 N resolution, 0–20 N:\u003c\/strong\u003e More than 300 taxels in seven regions read one-axis force in 0.1 N steps and withstand 200 N without damage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLeft hand of a sensing pair:\u003c\/strong\u003e Mirrored joints match the OmniHand 2025 Tactile right hand for bimanual robots.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e10 driven joints, 6 passive:\u003c\/strong\u003e The hand has 16 degrees of freedom in 180 mm and up to 550 g, with 0.3 mm fingertip repeatability.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTactile and hybrid control:\u003c\/strong\u003e A tactile mode joins position, torque, hybrid position-torque and velocity control, with tactile pressure in the feedback.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSimulation and ROS 2:\u003c\/strong\u003e Left- and right-hand URDF and MuJoCo models plus C++, Python and ROS 2 interfaces come with AgiBot's SDK.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"AGIBOT","offers":[{"title":"Default Title","offer_id":67633061658854,"sku":"AgiBot-OmniHand-2025-Tactile-Left","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/agibot-omnihand-2025-w-tactile-1_3.jpg?v=1791277763"},{"product_id":"casbot-handle-l1-pro-dexterous-robotic-hand","title":"Casbot Handle L1 Pro Tactile Dexterous Hand","description":"\u003cp\u003eThe Casbot Handle L1 Pro is the tactile version of Casbot's Handle L1 dexterous robotic hand: the same 11-degree-of-freedom, human-scale five-finger hand, with tactile sensors in the fingertips. They register a touch from 0.15 N, measure up to 20 N at 0.1 N resolution and respond within 5 ms, so a controller knows the moment a finger meets an object.\u003c\/p\u003e\u003cp\u003eThat contact data matters most where a grip has to be judged, not just commanded: eggs, tofu, potato chips, tissues and other fragile or soft objects, parts that may slip, and research into tactile grasping. Casbot specifies a consistency between contact points within ±10 %. Combined with the hand's adaptive force control and its position and force-position closed loops, the Pro suits labs and integrators building grasping that relies on touch.\u003c\/p\u003e\u003cp\u003eEverything else matches the standard hand. Six active and five passive joints give 11 degrees of freedom; the hand weighs about 610 g and measures 194 × 84 × 52 mm. Fingertips push with more than 10 N, pinch and lateral pinch reach 14 N and 25 N, and it holds over 10 kg in a vertical grip and over 25 kg in a flat grip or lift, across grip diameters of 16–95 mm. Repeatability is ±0.1 mm, and Casbot rates it for more than 1,000,000 fault-free cycles. It connects over RS-485, CAN FD or EtherCAT on 24–60 V, supports Windows, Linux, macOS and ROS 2, and is configured from a web page.\u003c\/p\u003e\u003cp\u003eIf your application does not need touch, the \u003ca href=\"\/en\/products\/casbot-handle-l1-dexterous-robotic-hand\"\u003estandard Casbot Handle L1\u003c\/a\u003e is the same hand without the fingertip sensors. Compare both with the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTactile fingertips from 0.15 N:\u003c\/strong\u003e Fingertip sensors register contact at 0.15 N and measure up to 20 N at 0.1 N resolution.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e5 ms tactile response:\u003c\/strong\u003e Touch data arrives within 5 ms, and readings between contact points stay within ±10 % of each other.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSame 11-DoF hand as the L1:\u003c\/strong\u003e Six active and five passive joints at 1:1 human-hand proportion, in a hand of about 610 g.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e25 kg lifting load:\u003c\/strong\u003e It holds over 10 kg in a vertical grip and over 25 kg in a flat grip or lift, with 14 N pinch and 25 N lateral pinch.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e±0.1 mm and 1,000,000 cycles:\u003c\/strong\u003e Fingertips repeat to ±0.1 mm, and Casbot rates the hand for over a million fault-free continuous cycles.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRS-485, CAN FD, EtherCAT:\u003c\/strong\u003e The hand runs on 24–60 V, supports Windows, Linux, macOS and ROS 2, and is configured from a web page.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Casbot","offers":[{"title":"Default Title","offer_id":67633061789926,"sku":"Casbot-Handle-L1-PRO","price":17200.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/cosbot_h1__1.jpg?v=1791277764"},{"product_id":"agibot-omnihand-2025-dexterous-right-robot-hand","title":"AgiBot OmniHand 2025 Dexterous Hand Right","description":"\u003cp\u003eThe AgiBot OmniHand 2025 is a compact five-finger dexterous robotic hand for interactive humanoid robots, and this is the right hand in the standard build, without tactile sensors. It has 16 degrees of freedom, 10 of them driven, in a body 180 mm long that weighs about 510 g, sized for humanoids of many makes as well as robot arms.\u003c\/p\u003e\u003cp\u003eAgiBot designed it for gesture interaction and light-duty tasks: the common interactive gestures, simple grasps and handling everyday objects. Its soft-touch coating and pinch-prevention design suit robots that work in receptions, showrooms, classrooms and labs. Each fingertip pushes with up to 5 N, the five-finger grip reaches at least 5 kg in hybrid force control mode, and fingertips repeat to 0.3 mm, opening or closing in 0.5 s.\u003c\/p\u003e\u003cp\u003eThe standard build controls its grip from the joints: position, torque, hybrid position-torque and velocity modes, with joint position, torque, speed and temperature fed back over CAN FD or RS-485 at 1 kHz, or over USB Type-C to a host computer. It runs on 24 V, mounts with four M4 screws at the wrist and updates its firmware over the air. AgiBot's SDK provides C++ and Python APIs, a kinematics library and a ROS 2 interface, and its left- and right-hand URDF and MuJoCo models cover simulation.\u003c\/p\u003e\u003cp\u003eFor a two-handed robot, pair it with the \u003ca href=\"\/en\/products\/agibot-omnihand-2025-dexterous-left-robot-hand\"\u003eOmniHand 2025 left hand\u003c\/a\u003e. If the robot should feel contact, the \u003ca href=\"\/en\/products\/agibot-omnihand-2025-tactile-right-robot-hand\"\u003eOmniHand 2025 Tactile right hand\u003c\/a\u003e adds force-sensing arrays across the fingers, palm and back of the hand, which enable AgiBot's back-of-hand touch interaction. Compare both with our other \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e16 degrees of freedom, 10 driven:\u003c\/strong\u003e The thumb has three driven joints, the index, ring and little fingers two each and the middle finger one, with six more joints following passively.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAbout 510 g at 180 mm:\u003c\/strong\u003e A 180 × 85 × 38.5 mm body in PA and silicone keeps the load on a humanoid's wrist low.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSoft-touch, pinch-safe build:\u003c\/strong\u003e A soft-touch coating and pinch-prevention design suit robots that gesture, hand over objects and work near people.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree ways to connect:\u003c\/strong\u003e CAN FD and RS-485 for the robot plus USB Type-C to a host computer, with 1 kHz communication and over-the-air firmware updates.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFour control modes:\u003c\/strong\u003e Position, torque, hybrid position-torque and velocity control, with joint position, torque, speed, temperature, voltage and current fed back.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSDK, ROS 2 and URDF:\u003c\/strong\u003e AgiBot's C++ and Python SDK includes a kinematics library and a ROS 2 interface, and left- and right-hand URDF and MuJoCo models cover simulation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"AGIBOT","offers":[{"title":"Default Title","offer_id":67633061855462,"sku":"AgiBot-OmniHand-2025","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/agibot-omnihand-2025-w-tactile-2_1.jpg?v=1791277764"},{"product_id":"agibot-omnihand-2025-dexterous-left-robot-hand","title":"AgiBot OmniHand 2025 Dexterous Hand Left","description":"\u003cp\u003eThis is the left hand of the AgiBot OmniHand 2025, AgiBot's compact interactive dexterous robotic hand, in the standard build without tactile sensors. Weighing about 510 g and measuring 180 × 85 × 38.5 mm, it brings 16 degrees of freedom to the left wrist of a humanoid robot or robot arm, and with the right hand it completes a two-handed setup.\u003c\/p\u003e\u003cp\u003eTen of its 16 joints are driven: three in the thumb, two each in the index, ring and little fingers and one in the middle finger, while six more follow passively so the fingers curl naturally around an object. A linkage transmission with motor and gear drive opens or closes the hand in 0.5 s, fingertips repeat to 0.3 mm and push with up to 5 N, and the five-finger grip reaches at least 5 kg in hybrid force control. The body is PA and silicone with a soft-touch coating and a pinch-prevention design, for robots that gesture and pass things to people.\u003c\/p\u003e\u003cp\u003eFor development teams, the hand talks CAN FD or RS-485 at 1 kHz and connects to a host computer over USB Type-C. AgiBot's SDK provides C++ and Python APIs with a kinematics library and a ROS 2 interface, and left- and right-hand URDF and MuJoCo models let you test grasps in simulation first. Control runs in position, torque, hybrid position-torque or velocity mode on 24 V, and the firmware updates over the air.\u003c\/p\u003e\u003cp\u003ePair it with the \u003ca href=\"\/en\/products\/agibot-omnihand-2025-dexterous-right-robot-hand\"\u003eOmniHand 2025 right hand\u003c\/a\u003e for bimanual work. For contact sensing, choose the \u003ca href=\"\/en\/products\/agibot-omnihand-2025-tactile-left-robot-hand\"\u003eOmniHand 2025 Tactile left hand\u003c\/a\u003e, which adds force-sensing arrays over the fingers, palm and back of the hand; for higher force and 19 degrees of freedom, see the \u003ca href=\"\/en\/products\/agibot-omnihand-pro-2025-five-finger-dexterous-hand\"\u003eOmniHand Pro 2025\u003c\/a\u003e. All of them sit among our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuilt for the left wrist:\u003c\/strong\u003e Mirrored joints make this the left hand of a pair, with the same specification as the OmniHand 2025 right hand.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTen driven joints, six passive:\u003c\/strong\u003e The passive joints follow the driven ones so the five fingers curl around an object, giving 16 degrees of freedom in all.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.3 mm fingertip repeatability:\u003c\/strong\u003e Fingertips return to within 0.3 mm, and the hand opens or closes in 0.5 s.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e5 kg five-finger grip:\u003c\/strong\u003e In hybrid force control mode the five-finger grip reaches at least 5 kg, with up to 5 N at each fingertip.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSimulation-ready:\u003c\/strong\u003e AgiBot provides left- and right-hand URDF and MuJoCo models, and its SDK adds C++ and Python APIs, kinematics and ROS 2.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCAN FD, RS-485 or USB:\u003c\/strong\u003e The hand runs on 24 V, communicates at 1 kHz and takes firmware updates over the air.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"AGIBOT","offers":[{"title":"Default Title","offer_id":67633061953766,"sku":"AgiBot-OmniHand-2025-Left","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/agibot-omnihand-2025-w-tactile-2_1_1.jpg?v=1791277763"},{"product_id":"casbot-handle-l1-dexterous-robotic-hand","title":"Casbot Handle L1 Dexterous Hand","description":"\u003cp\u003eThe Casbot Handle L1 is Casbot's lightweight, highly integrated five-finger dexterous robotic hand, built at 1:1 human-hand proportion for humanoid robots, robot arms and teleoperation systems. This is the standard version, without fingertip tactile sensors. It has 11 degrees of freedom, six of them active, weighs about 610 g and measures 194 × 84 × 52 mm.\u003c\/p\u003e\u003cp\u003eCasbot built it for strength and endurance. Each of the four fingertips pushes with more than 10 N, pinch and lateral pinch reach 14 N and 25 N, and the hand holds more than 10 kg in a vertical grip and over 25 kg in a flat grip or lift. Adaptive force control lets the same hand pick up fragile, soft and irregular items, from eggs, tofu and potato chips to tissues and business cards, across grip diameters of 16 to 95 mm. Casbot rates it for more than 1,000,000 fault-free continuous cycles, with ±0.1 mm fingertip repeatability and resistance to accidental impacts and drops.\u003c\/p\u003e\u003cp\u003eIntegration is quick: the hand uses an open interface protocol over RS-485, CAN FD or EtherCAT on a 24–60 V supply, works with Windows, Linux, macOS and ROS 2, and is configured from a web page without host software. Built-in preset commands for grasping, pinching, pointing, pressing, hooking and lifting help it adapt quickly to robot arms and teleoperation systems. That makes it a fit for research and teaching labs, light production tasks such as moving material and pressing buttons, and service robots that shake hands or point the way.\u003c\/p\u003e\u003cp\u003eThe \u003ca href=\"\/en\/products\/casbot-handle-l1-pro-dexterous-robotic-hand\"\u003eCasbot Handle L1 Pro\u003c\/a\u003e is the same hand with tactile fingertips, measuring 0.15–20 N at 0.1 N resolution with a response within 5 ms, for grasping that relies on contact data. Compare both with the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e11 degrees of freedom at human scale:\u003c\/strong\u003e Six active and five passive joints work together in a five-finger hand built to 1:1 human-hand proportion.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOver 25 kg static lifting load:\u003c\/strong\u003e The hand holds more than 10 kg in a vertical grip and over 25 kg in a flat grip or lift, with more than 10 N at each fingertip.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e14 N pinch, 25 N side pinch:\u003c\/strong\u003e Pinch and lateral pinch reach 14 N and 25 N, and the grip spans objects from 16 to 95 mm across.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e±0.1 mm, over a million cycles:\u003c\/strong\u003e Fingertips repeat to ±0.1 mm, and Casbot rates the hand for more than 1,000,000 fault-free continuous cycles.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree industrial buses:\u003c\/strong\u003e RS-485, CAN FD and EtherCAT run on a 24–60 V supply, and the hand draws 80 mA at rest.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeb setup, ROS 2 support:\u003c\/strong\u003e The hand is configured from a web page without host software, carries preset commands and works with Windows, Linux, macOS and ROS 2.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Casbot","offers":[{"title":"Default Title","offer_id":67633062019302,"sku":"Casbot-Handle-L1","price":14350.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/cosbot_h1.jpg?v=1791277763"},{"product_id":"brainco-revo-1-intelligent-dexterous-bionic-hand","title":"BrainCo Revo 1 Bionic Hand","description":"\u003cp\u003eThe BrainCo Revo 1 is BrainCo's first-generation bionic dexterous robotic hand, a five-finger hand for the left or right side that grew out of the company's prosthetic hand work. Six precision micro-motors give it 10 degrees of freedom, and it weighs 545 g, measuring 183 mm from palm base to middle fingertip and 86 mm across the palm.\u003c\/p\u003e\u003cp\u003eIts strength is load: 50 N across five fingers, up to 8 kg on a single finger and 30 kg for the whole hand, with the thumb and index finger opening 113 mm apart and a control precision of 0.1 mm. Three grip-force levels, position and speed control and a turbo mode that re-grips after a stall help it hold soft or shifting objects, and BrainCo rates the fingers for 300,000 open-close cycles. That makes it a sturdy hand for research labs, teaching robots and human-machine interface projects that value payload over the lowest mass.\u003c\/p\u003e\u003cp\u003eBrainCo builds the Revo 1 in three versions. The Basic connects over RS-485 with the open Modbus-RTU protocol or over CAN, on 9.5–28 V, with a 30 N single-finger pinch. The Touch adds a sensor in each fingertip that measures normal pressure, shear force, force direction and proximity up to 1 cm, from 0.1 N to a configurable 25 N with 5 % full-scale accuracy. The Advanced runs RS-485, CAN FD and EtherCAT on 12–78 V. The version, hand side and interface are confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eThe newer \u003ca href=\"\/en\/products\/brainco-revo-2-basic-left-dexterous-bionic-hand-xrl\"\u003eRevo 2 Basic\u003c\/a\u003e and \u003ca href=\"\/en\/products\/brainco-revo-2-touch-biomimetic-dexterous-left-hand\"\u003eRevo 2 Touch\u003c\/a\u003e put 11 degrees of freedom into 383 g and carry 20 kg; the Revo 1 is heavier and carries more. BrainCo's Python and C\/C++ SDK, a desktop tool for Windows and Ubuntu, a ROS URDF model and a MuJoCo model support integration and simulation. Compare both generations with our other \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e30 kg whole-hand payload:\u003c\/strong\u003e Each finger holds up to 8 kg and the whole hand up to 30 kg, with a 50 N five-finger grip.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e10 degrees of freedom from six motors:\u003c\/strong\u003e Six precision micro-motors drive thumb flexion and abduction and the flexion of each finger, and each finger adds a passive joint.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree builds:\u003c\/strong\u003e The Basic runs RS-485 and CAN on 9.5–28 V, the Touch adds fingertip tactile sensors, and the Advanced runs RS-485, CAN FD and EtherCAT on 12–78 V.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFingertip sensing on the Touch:\u003c\/strong\u003e Its sensors measure normal pressure, shear force, force direction and proximity up to 1 cm, from 0.1 N to a configurable 25 N, at 50 Hz or more.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRated for 300,000 finger cycles:\u003c\/strong\u003e BrainCo rates finger life at 300,000 open-close cycles, on a frame of aviation aluminium alloy and food-grade plastic.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSDK, ROS and MuJoCo models:\u003c\/strong\u003e BrainCo's Python and C\/C++ SDK, a desktop tool for Windows and Ubuntu, a ROS URDF model and a MuJoCo model support development and simulation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"BrainCo","offers":[{"title":"Default Title","offer_id":67633062379750,"sku":"BrainCo-Dexterous-Bionic-Hand","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/brainco_6.jpg?v=1791277764"},{"product_id":"brainco-revo-2-basic-left-dexterous-bionic-hand-xrl","title":"BrainCo Revo 2 Basic Bionic Hand Left (XRL)","description":"\u003cp\u003eThe BrainCo Revo 2 Basic (XRL) is the left-hand Basic version of BrainCo's Revo 2 bionic dexterous robotic hand: the same 383 g, 11-degree-of-freedom mechanism as the Pro and Touch, without EtherCAT or fingertip sensors. Six coreless motors drive the thumb's flexion and abduction and the flexion of each finger, five passive joints follow them, and the hand measures 160 mm from palm base to middle fingertip and 78.5 mm across the palm.\u003c\/p\u003e\u003cp\u003eIt suits labs, teaching programmes and humanoid builders who need a capable human-sized hand on a standard serial bus. A DIP switch under the wrist cover selects Modbus-RTU over RS-485 or CAN FD, both at up to 500 Hz, and the hand runs on 12–28 V, idling at 65 mA at 24 V. BrainCo's Python and C\/C++ SDKs cover Linux, Windows and ROS, with URDF and MuJoCo models for simulation and over-the-air firmware updates.\u003c\/p\u003e\u003cp\u003eStrength matches the rest of the range: at least 50 N five-finger grip, 15 N pinch, a 20 kg payload, 0.1° repeat precision and a full flex or extension in 0.65 s or less, at no more than 50 dB. The \u003ca href=\"\/en\/products\/brainco-revo-2-pro-dexterous-left-hand-xel\"\u003eRevo 2 Pro left hand (XEL)\u003c\/a\u003e adds EtherCAT at up to 1 kHz and a 12–64 V input, and the \u003ca href=\"\/en\/products\/brainco-revo-2-touch-biomimetic-dexterous-left-hand\"\u003eRevo 2 Touch left hand (XTL)\u003c\/a\u003e adds capacitive sensors in all five fingertips on top of that.\u003c\/p\u003e\u003cp\u003eThis hand is set to device ID 126; the \u003ca href=\"\/en\/products\/brainco-revo-2-basic-right-dexterous-bionic-hand-xrr\"\u003eRevo 2 Basic right hand (XRR)\u003c\/a\u003e uses 127, so a pair can share one bus. The box holds the hand and one RS-485\/CAN FD cable. For a Unitree H2 there is a \u003ca href=\"\/en\/products\/brainco-revo-2-basic-dexterous-hand-for-h2\"\u003eRevo 2 Basic hand configured for the H2\u003c\/a\u003e, and our full range of \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e covers other makers.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLowest power draw in the Revo 2 range:\u003c\/strong\u003e At 24 V the Basic idles at 65 mA and averages 350 mA flexing all five fingers with no load, on a 12–28 V supply.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRS-485 or CAN FD by switch:\u003c\/strong\u003e A DIP switch under the wrist cover selects Modbus-RTU over RS-485 or CAN FD, both at up to 500 Hz, on one five-pin connector.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e383 g with a 20 kg payload:\u003c\/strong\u003e The hand weighs 383 g, grips with at least 50 N, pinches with at least 15 N and carries at least 20 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e11 degrees of freedom:\u003c\/strong\u003e Six coreless motors drive two thumb joints and one joint per finger, five further joints follow passively, and positions repeat to 0.1°.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCascaded and compliance control:\u003c\/strong\u003e Besides position, velocity and current control, the Basic runs cascaded and compliance control, and a turbo mode keeps re-gripping soft or shifting objects.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePython, C\/C++ and ROS:\u003c\/strong\u003e BrainCo's SDKs run on Linux, Windows and ROS, URDF and MuJoCo models are provided, and the firmware updates over the air.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"BrainCo","offers":[{"title":"Default Title","offer_id":67633064214758,"sku":"BrainCo-Revo-2-Basic-Left","price":12650.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/brainco-revo-2-silver-r_2_1_1.jpg?v=1791277767"},{"product_id":"brainco-revo-2-basic-right-dexterous-bionic-hand-xrr","title":"BrainCo Revo 2 Basic Bionic Hand Right (XRR)","description":"\u003cp\u003eThe BrainCo Revo 2 Basic Right (XRR) is the right-hand bionic dexterous robotic hand that starts BrainCo's Revo 2 range. It weighs 383 g, which BrainCo compares to a bottle of water, measures 160 mm from palm base to middle fingertip, and moves five fingers through 11 degrees of freedom with six coreless motors.\u003c\/p\u003e\u003cp\u003eChoose the Basic when the controller already speaks RS-485 or CAN and the work is grasping rather than sensing: pick-and-place, teleoperation, demonstration robots and manipulation courses. A DIP switch under the wrist cover sets Modbus-RTU over RS-485 or CAN FD, each at up to 500 Hz; the supply is 12–28 V, and at 24 V the hand draws 65 mA at rest and 350 mA on average while flexing without load. Position, velocity, current, cascaded and compliance control are all built in, and a turbo mode re-grips soft or shifting objects every 500 ms after a stall.\u003c\/p\u003e\u003cp\u003eThe fingers close with at least 50 N, pinch with 15 N and hold at least 20 kg, open 100 mm between thumb and index finger, and complete a flex or extension in 0.65 s or less. Moving up the range keeps that hardware: the \u003ca href=\"\/en\/products\/brainco-revo-2-pro-dexterous-right-hand-xer\"\u003eRevo 2 Pro right hand (XER)\u003c\/a\u003e adds EtherCAT at up to 1 kHz and a 12–64 V input, and the \u003ca href=\"\/en\/products\/brainco-revo-2-touch-biomimetic-dexterous-right-hand\"\u003eRevo 2 Touch right hand (XTR)\u003c\/a\u003e also senses with all five fingertips.\u003c\/p\u003e\u003cp\u003eOut of the box the XRR answers to device ID 127, while the \u003ca href=\"\/en\/products\/brainco-revo-2-basic-left-dexterous-bionic-hand-xrl\"\u003eRevo 2 Basic left hand (XRL)\u003c\/a\u003e answers to 126, so both hands of a humanoid run on one bus. Each comes with an RS-485\/CAN FD cable, and BrainCo's Python and C\/C++ SDKs, URDF and MuJoCo models and over-the-air firmware updates support it on Linux, Windows and ROS. Compare it with the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e11 degrees of freedom on six motors:\u003c\/strong\u003e The thumb gets driven flexion and abduction, each finger a driven flexion joint coupled to a passive one, and every position repeats to 0.1°.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e20 kg from a 383 g hand:\u003c\/strong\u003e A five-finger grip of at least 50 N and a 15 N pinch let the 383 g right hand carry at least 20 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne connector, two protocols:\u003c\/strong\u003e The DIP switch under the wrist cover sets Modbus-RTU over RS-485 or CAN FD, and either one reaches 500 Hz.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLight on power:\u003c\/strong\u003e The Basic takes 12–28 V and draws 65 mA at rest and 4.6 A at peak at 24 V, the lowest figures in the Revo 2 range.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuilt-in protection:\u003c\/strong\u003e Current, stall, over-temperature and collision protection guard the motors, and a light on the back of the hand shows power-up, low voltage, OTA and fault states.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOpen SDK and simulation models:\u003c\/strong\u003e Python and C\/C++ SDKs for Linux, Windows and ROS come with URDF and MuJoCo models of the hand.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"BrainCo","offers":[{"title":"Default Title","offer_id":67633064280294,"sku":"BrainCo-Revo-2-Basic","price":12650.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/brainco-revo-2-silver-r_2_1.jpg?v=1791277767"},{"product_id":"brainco-revo-2-pro-dexterous-left-hand-xel","title":"BrainCo Revo 2 Pro Bionic Hand Left (XEL)","description":"\u003cp\u003eThe BrainCo Revo 2 Pro (XEL) is the left-hand Pro version of BrainCo's Revo 2 bionic dexterous robotic hand, built for robots that run their joints on EtherCAT. It keeps the Revo 2 mechanism, 383 g with 11 degrees of freedom from six coreless motors, and adds an EtherCAT port and a 12–64 V input to the RS-485 and CAN FD of the Basic.\u003c\/p\u003e\u003cp\u003eEtherCAT matters when the hand has to move in step with the arm. With CoE and PDO the Pro exchanges commands and state at up to 1 kHz, where RS-485 and CAN FD top out at 500 Hz, so a humanoid or arm controller can treat the fingers as more axes in the same cycle. The wide supply runs straight from a 24 V or 48 V rail, and at 24 V the hand idles at 115 mA and peaks at 4.65 A. Position, velocity, current, cascaded and compliance control and five command modes (position with a time or speed limit, speed, current and PWM) come with BrainCo's Python and C\/C++ SDKs on Linux, Windows and ROS.\u003c\/p\u003e\u003cp\u003eThe hand measures 160 mm from palm base to middle fingertip and 78.5 mm across the palm, grips with at least 50 N, pinches with 15 N, carries at least 20 kg and repeats to 0.1°. The \u003ca href=\"\/en\/products\/brainco-revo-2-basic-left-dexterous-bionic-hand-xrl\"\u003eRevo 2 Basic left hand (XRL)\u003c\/a\u003e is the same hand on RS-485 or CAN FD only, at 12–28 V, and the \u003ca href=\"\/en\/products\/brainco-revo-2-touch-biomimetic-dexterous-left-hand\"\u003eRevo 2 Touch left hand (XTL)\u003c\/a\u003e is the Pro with capacitive tactile sensors in every fingertip and tactile adaptive control.\u003c\/p\u003e\u003cp\u003eThis is the left hand, device ID 126 by default; the \u003ca href=\"\/en\/products\/brainco-revo-2-pro-dexterous-right-hand-xer\"\u003eRevo 2 Pro right hand (XER)\u003c\/a\u003e uses 127, and both arrive with RS-485\/CAN FD, EtherCAT and power cables. The wrist mounts with four M3 screws into 3.5 mm threaded holes, so screws should enter no more than 3 mm; fitment to your arm is confirmed with the quotation. See our other \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e for different makers and designs.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT at up to 1 kHz:\u003c\/strong\u003e EtherCAT with CoE and PDO runs at up to 1 kHz, twice the 500 Hz of the RS-485 and CAN FD ports the Pro also carries.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e12–64 V supply:\u003c\/strong\u003e The wide input runs from a 24 V or 48 V rail; at 24 V the hand draws 115 mA at rest and 4.65 A at peak.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eA connector for each bus:\u003c\/strong\u003e RS-485, CAN FD and EtherCAT each have their own connector under the wrist, beside an XT30 power input.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e383 g, 20 kg payload:\u003c\/strong\u003e The left hand weighs 383 g, grips with at least 50 N, pinches with at least 15 N and carries at least 20 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e11 degrees of freedom:\u003c\/strong\u003e Six coreless motors drive the thumb's flexion and abduction and each finger's flexion, five joints follow passively, and control repeats to 0.1°.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePython, C\/C++ and ROS:\u003c\/strong\u003e BrainCo's SDKs run on Linux, Windows and ROS, with URDF and MuJoCo models and over-the-air firmware updates.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"BrainCo","offers":[{"title":"Default Title","offer_id":67633064378598,"sku":"BrainCo-Revo-2-Pro-Left","price":15600.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/brainco-revo-2-silver-r_2_2.jpg?v=1791277767"},{"product_id":"brainco-revo-2-pro-dexterous-right-hand-xer","title":"BrainCo Revo 2 Pro Bionic Hand Right (XER)","description":"\u003cp\u003eThe BrainCo Revo 2 Pro Right (XER) is the right-hand bionic dexterous robotic hand of BrainCo's Revo 2 Pro version, the step up from the Basic for robots built around EtherCAT. Its five fingers carry 11 degrees of freedom, six of them driven by coreless motors, in a hand of 383 g that is 160 mm long and 78.5 mm across the palm.\u003c\/p\u003e\u003cp\u003eMany humanoids and collaborative arms run their joints on EtherCAT, and the XER joins that network directly: CoE and PDO at up to 1 kHz, with RS-485 (Modbus-RTU) and CAN FD at up to 500 Hz on separate connectors for simpler setups. It runs from 12 to 64 V through an XT30 connector and draws 115 mA at rest at 24 V. The control stack is the same across the Revo 2: position, velocity and current control with cascaded and compliance control, five command modes and a turbo mode that keeps re-gripping a soft or shifting object after a stall.\u003c\/p\u003e\u003cp\u003eMechanically the Pro equals the other Revo 2 versions: at least 50 N grip, 15 N pinch, a payload of at least 20 kg, 100 mm opening between thumb and index finger, 0.1° repeat precision and 0.65 s or less per flex or extension. The \u003ca href=\"\/en\/products\/brainco-revo-2-basic-right-dexterous-bionic-hand-xrr\"\u003eRevo 2 Basic right hand (XRR)\u003c\/a\u003e drops EtherCAT and runs on 12–28 V; the \u003ca href=\"\/en\/products\/brainco-revo-2-touch-biomimetic-dexterous-right-hand\"\u003eRevo 2 Touch right hand (XTR)\u003c\/a\u003e keeps the Pro's interfaces and adds a capacitive tactile sensor in every fingertip.\u003c\/p\u003e\u003cp\u003eOut of the box the XER uses device ID 127 and the \u003ca href=\"\/en\/products\/brainco-revo-2-pro-dexterous-left-hand-xel\"\u003eRevo 2 Pro left hand (XEL)\u003c\/a\u003e 126, so a two-handed robot addresses both on one bus. The package holds the hand with RS-485\/CAN FD, EtherCAT and power cables; BrainCo's Python and C\/C++ SDKs run on Linux, Windows and ROS, and the firmware updates over the air. For other makes and models, see our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT for real-time arms:\u003c\/strong\u003e CoE and PDO over EtherCAT give a control rate of up to 1 kHz, so the fingers can run in the same cycle as an EtherCAT arm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree interfaces, one hand:\u003c\/strong\u003e EtherCAT, CAN FD and RS-485 (Modbus-RTU) each have a connector under the wrist; the two serial buses run at up to 500 Hz.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRuns from 12 to 64 V:\u003c\/strong\u003e At 24 V it draws 115 mA standing still, 390 mA on average flexing with no load and 4.65 A at most.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSix motors, 11 degrees of freedom:\u003c\/strong\u003e Driven thumb flexion (0–59°) and abduction (0–90°), driven flexion in each finger (0–81°) and five passive joints repeat to 0.1°.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAt least 50 N grip:\u003c\/strong\u003e The 383 g hand grips with at least 50 N, pinches with 15 N and holds at least 20 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSimulation-ready:\u003c\/strong\u003e URDF models for ROS 1 and ROS 2 and a MuJoCo model sit alongside BrainCo's Python and C\/C++ SDKs.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"BrainCo","offers":[{"title":"Default Title","offer_id":67633064444134,"sku":"BrainCo-Revo-2-Pro","price":15600.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/brainco-revo-2-silver-r_2.jpg?v=1791277766"},{"product_id":"brainco-revo-3-21-basic-dexterous-robot-hand","title":"BrainCo Revo 3-21 Basic Dexterous Hand (U21)","description":"\u003cp\u003eThe BrainCo Revo 3-21 Basic is BrainCo's 21-degree-of-freedom dexterous robotic hand in its base build, Revo 3 U21, without tactile sensors, made as a left or a right hand. Each of its 21 joints has its own direct-drive, backdrivable motor: five in the thumb and four in each finger, so every finger flexes at three joints and spreads sideways at the knuckle.\u003c\/p\u003e\u003cp\u003eThat joint count is what separates the Revo 3 from the 11-degree-of-freedom Revo 2. BrainCo reports a full Kapandji opposition score and all 33 grasps of the Feix GRASP taxonomy, on objects from 10 mm to 150 mm across, which opens up in-hand manipulation: turning, re-gripping and using tools rather than only closing on them. The hand grips with at least 100 N, pinches with at least 25 N, carries 20 kg (5 kg on four fingers), moves a joint from open to close in 0.33 s and repeats to 0.1°.\u003c\/p\u003e\u003cp\u003eIt is aimed at embodied-AI and humanoid research teams, universities and robot makers training manipulation policies. Control runs at 500 Hz over EtherCAT, CAN FD or RS-485 in position, MIT force-position, current, admittance or impedance mode, from a 16–85 V supply, and an IMU and a temperature sensor sit on the mainboard. BrainCo provides Python and C\/C++ SDKs, a ROS 2 Humble driver, URDF, MuJoCo and Isaac Sim models, and reinforcement-learning, VLA and teleoperation demos. Core joints are rated for 1,000,000 flex cycles.\u003c\/p\u003e\u003cp\u003eAll Revo 3 versions share these specifications and differ only in sensing. The \u003ca href=\"\/en\/products\/brainco-revo-3-21-touch-dexterous-robot-hand\"\u003eRevo 3-21 Touch (U21T)\u003c\/a\u003e adds a 451-point pressure array, and the \u003ca href=\"\/en\/products\/brainco-revo-3-21-v-touch-visuotactile-robot-hand\"\u003eRevo 3-21 V-Touch (U21VT)\u003c\/a\u003e combines a 336-point palm array with visuotactile fingertips. For a Unitree H2, see the \u003ca href=\"\/en\/products\/unitree-h2-edu-brainco-revo-3-u21-dexterous-hand-with-rgb\"\u003eRevo 3 U21 hand for the H2 EDU\u003c\/a\u003e. Choose the Basic when motor position and current feedback are enough, or compare the Revo 2 range and other makers among our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e21 active degrees of freedom:\u003c\/strong\u003e Every joint has its own motor: five in the thumb and four in each finger, including sideways spread at each knuckle.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDirect-drive, backdrivable joints:\u003c\/strong\u003e With no gearbox between motor and joint, the fingers yield to outside force, and BrainCo designs them for millisecond response and compliant, safe contact.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e100 N grip, 20 kg payload:\u003c\/strong\u003e The hand grips with at least 100 N, pinches with at least 25 N and holds 20 kg in the whole hand or 5 kg on four fingers.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e33 grasp patterns:\u003c\/strong\u003e BrainCo reports a full Kapandji opposition score and all 33 grasps of the Feix GRASP taxonomy, on objects 10 to 150 mm across.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.33 s open to close:\u003c\/strong\u003e Joints travel open to close in 0.33 s and repeat to 0.1° under position, MIT force-position, current, admittance or impedance control at 500 Hz.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT, CAN FD and RS-485 on 16–85 V:\u003c\/strong\u003e Three industrial buses and a wide supply input let the hand run from a humanoid's main power rail.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOpen software stack:\u003c\/strong\u003e Python and C\/C++ SDKs, a ROS 2 Humble driver and URDF, MuJoCo and Isaac Sim models come with reinforcement-learning and teleoperation demos.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"BrainCo","offers":[{"title":"Default Title","offer_id":67633064542438,"sku":"BrainCo-Revo-3","price":62750.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/brainco-revo-3-21-basic-robot-hand-right.jpg?v=1791277768"},{"product_id":"brainco-revo-3-21-touch-dexterous-robot-hand","title":"BrainCo Revo 3-21 Touch Dexterous Hand (U21T)","description":"\u003cp\u003eThe BrainCo Revo 3-21 Touch is the tactile build of BrainCo's Revo 3 dexterous robotic hand, model U21T, made as a left or a right hand. It adds a piezoresistive pressure array of 451 sensing points to the Revo 3's 21 fully active, direct-drive and backdrivable joints.\u003c\/p\u003e\u003cp\u003eThe array reads from 0 to 20 N at 0.01 N resolution and 100 Hz, and BrainCo renders it as a real-time contact heatmap, so a controller sees where an object touches the hand and how hard. Together with motor-current feedback from the backdrivable joints, that is the data contact-rich tasks need: re-gripping a tool, keeping a light hold on a fragile part, or recording tactile demonstrations for imitation and reinforcement learning. It suits robot makers and industrial research labs where a grasp has to be checked, not assumed.\u003c\/p\u003e\u003cp\u003eUnderneath, it is the full Revo 3: five joints in the thumb and four in each finger, at least 100 N grip and 25 N pinch, a 20 kg payload (5 kg on four fingers), 0.33 s open to close, 0.1° repeatability and a 10–150 mm grasp range covering BrainCo's 33 grasp patterns. It runs at 500 Hz over EtherCAT, CAN FD or RS-485 on 16–85 V, with Python and C\/C++ SDKs, a ROS 2 Humble driver and URDF, MuJoCo and Isaac Sim models.\u003c\/p\u003e\u003cp\u003eSensing is the only difference across the Revo 3 range. The \u003ca href=\"\/en\/products\/brainco-revo-3-21-basic-dexterous-robot-hand\"\u003eRevo 3-21 Basic (U21)\u003c\/a\u003e has no tactile array, and the \u003ca href=\"\/en\/products\/brainco-revo-3-21-v-touch-visuotactile-robot-hand\"\u003eRevo 3-21 V-Touch (U21VT)\u003c\/a\u003e pairs a 336-point palm array with visuotactile fingertips. For a Unitree H2, see the \u003ca href=\"\/en\/products\/brainco-revo-3-u21t-tactile-dexterous-hand\"\u003eRevo 3 U21T tactile hand configured for the H2\u003c\/a\u003e, or compare all our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e451 sensing points:\u003c\/strong\u003e A piezoresistive array maps contact pressure across the hand, which BrainCo shows as a real-time contact heatmap.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.01 N resolution:\u003c\/strong\u003e Each sensing point reads from 0 to 20 N in 0.01 N steps, sampled at 100 Hz.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e21 direct-drive degrees of freedom:\u003c\/strong\u003e Five joints in the thumb and four in each finger, all active and backdrivable, so motor current also reflects contact at every joint.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e100 N grip, 25 N pinch:\u003c\/strong\u003e The hand carries 20 kg in the whole hand or 5 kg on four fingers, and moves a joint from open to close in 0.33 s.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e33 grasp patterns:\u003c\/strong\u003e BrainCo reports a full Kapandji opposition score and every grasp of the Feix GRASP taxonomy, on objects 10 to 150 mm across.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e500 Hz on three buses:\u003c\/strong\u003e EtherCAT, CAN FD and RS-485 carry joint control at 500 Hz, with a separate connector for tactile data, on a 16–85 V supply.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSimulation and learning tools:\u003c\/strong\u003e Python and C\/C++ SDKs, a ROS 2 Humble driver and URDF, MuJoCo and Isaac Sim models support sim-to-real work.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"BrainCo","offers":[{"title":"Default Title","offer_id":67633064607974,"sku":"BrainCo-Revo-3-Touch","price":77750.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/brainco-revo-3-21-basic-robot-hand-right_1.jpg?v=1791277768"},{"product_id":"brainco-revo-3-21-v-touch-visuotactile-robot-hand","title":"BrainCo Revo 3-21 V-Touch Dexterous Hand (U21VT)","description":"\u003cp\u003eThe BrainCo Revo 3-21 V-Touch is the visuotactile build of BrainCo's Revo 3 dexterous robotic hand, model U21VT, made as a left or a right hand. It is the most heavily sensed Revo 3: a piezoresistive pressure array of 336 points in the palm and visuotactile imaging in the fingertips, on the same 21 fully active, direct-drive and backdrivable joints as the rest of the range.\u003c\/p\u003e\u003cp\u003eThe two layers answer different questions. The palm array maps where and how hard an object presses, from 0 to 20 N at 0.01 N resolution; the fingertip sensors image the contact surface through 2,000 markers, which BrainCo uses to capture fine texture and slip. BrainCo calls this pairing of full-palm arrays and fingertip visuotactile sensing an industry first. It suits research on in-hand manipulation, slip detection, material recognition and learning from touch, where fingertip images become training data.\u003c\/p\u003e\u003cp\u003eMechanically and electrically it matches the other Revo 3 versions: five joints in the thumb and four per finger, at least 100 N grip and 25 N pinch, a 20 kg payload, 0.33 s open to close, 0.1° repeatability, 33 grasp patterns on objects of 10–150 mm, and 500 Hz control over EtherCAT, CAN FD or RS-485 on 16–85 V. BrainCo supports it with Python and C\/C++ SDKs, a ROS 2 Humble driver, URDF, MuJoCo and Isaac Sim models and open reinforcement-learning, VLA and teleoperation demos.\u003c\/p\u003e\u003cp\u003eIf palm pressure alone is enough, the \u003ca href=\"\/en\/products\/brainco-revo-3-21-touch-dexterous-robot-hand\"\u003eRevo 3-21 Touch (U21T)\u003c\/a\u003e carries a 451-point array, and the \u003ca href=\"\/en\/products\/brainco-revo-3-21-basic-dexterous-robot-hand\"\u003eRevo 3-21 Basic (U21)\u003c\/a\u003e has no tactile sensors. For a Unitree H2 there is a \u003ca href=\"\/en\/products\/brainco-revo-3-u21v-visuo-tactile-hand\"\u003eRevo 3 visuo-tactile hand configured for the H2\u003c\/a\u003e, and our other \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e cover the Revo 2 and other makers.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eVisuotactile fingertips:\u003c\/strong\u003e Visuotactile imaging in the fingertips, with 2,000 markers, captures fine surface texture and slip.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e336-point palm array:\u003c\/strong\u003e A piezoresistive array maps pressure across the palm from 0 to 20 N at 0.01 N resolution, sampled at 100 Hz.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e21 direct-drive degrees of freedom:\u003c\/strong\u003e Five thumb joints and four per finger, each with its own backdrivable motor, give compliant contact and full opposition.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e33 grasp patterns, 10–150 mm:\u003c\/strong\u003e BrainCo reports a full Kapandji score and all 33 grasps of the Feix GRASP taxonomy, from 10 mm to 150 mm objects.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e100 N grip, 20 kg payload:\u003c\/strong\u003e The hand grips with at least 100 N, pinches with 25 N and carries 20 kg, or 5 kg on four fingers.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e500 Hz on three buses:\u003c\/strong\u003e Joint control runs at 500 Hz over EtherCAT, CAN FD or RS-485 on a 16–85 V supply.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSim-to-real software:\u003c\/strong\u003e Python and C\/C++ SDKs, a ROS 2 Humble driver and URDF, MuJoCo and Isaac Sim models come with reinforcement-learning, VLA and teleoperation demos.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"BrainCo","offers":[{"title":"Default Title","offer_id":67633064706278,"sku":"BrainCo-Revo-3-V-Touch","price":129250.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/brainco-revo-3-21-basic-robot-hand-right_1_1.jpg?v=1791277767"},{"product_id":"brainco-revo-2-touch-biomimetic-dexterous-left-hand","title":"BrainCo Revo 2 Touch Bionic Hand Left (XTL)","description":"\u003cp\u003eThe BrainCo Revo 2 Touch (XTL) is the left-hand version of BrainCo's Revo 2 bionic dexterous hand with tactile fingertips, the only one of the three Revo 2 versions that can feel what it holds. It weighs 383 g, measures 160 mm from palm base to middle fingertip and 78.5 mm across the palm, and gives a humanoid robot or robot arm 11 degrees of freedom, six of them driven by their own motors.\u003c\/p\u003e\u003cp\u003eChoose the Touch when the task depends on contact. A capacitive module in each of the five fingertips reads pressure, friction, force direction and proximity, measuring normal and tangential force up to 25 N at 70 Hz, so a controller can notice an object before touching it, detect first contact and set the grip before a paper cup folds or a smooth part slips. The tactile adaptive control mode works this way, and BrainCo's Python adaptive-grasping example recognises object stiffness from the fingertip data. That makes it a strong fit for grasp-learning research, teleoperation and humanoids that handle fragile or mixed objects.\u003c\/p\u003e\u003cp\u003eStrength is the same across the Revo 2 range: at least 50 N five-finger grip, 15 N pinch, a 20 kg maximum payload, 0.1° repeat control precision and a full flex or extension in 0.65 s or less, at 50 dB or less. The \u003ca href=\"\/en\/products\/brainco-revo-2-basic-left-dexterous-bionic-hand-xrl\"\u003eRevo 2 Basic left hand (XRL)\u003c\/a\u003e connects over RS-485 or CAN FD on 12–28 V, the \u003ca href=\"\/en\/products\/brainco-revo-2-pro-dexterous-left-hand-xel\"\u003eRevo 2 Pro left hand (XEL)\u003c\/a\u003e adds EtherCAT and a 12–64 V input, and the Touch keeps everything the Pro has and adds the fingertip sensors.\u003c\/p\u003e\u003cp\u003eThis is the left hand, with default device ID 126; the matching \u003ca href=\"\/en\/products\/brainco-revo-2-touch-biomimetic-dexterous-right-hand\"\u003eRevo 2 Touch right hand (XTR)\u003c\/a\u003e uses 127, so a pair is addressed separately from the first power-on. Both run BrainCo's Python and C\/C++ SDKs on Linux, Windows and ROS, update over the air and connect at up to 500 Hz over RS-485 or CAN FD, or 1 kHz over EtherCAT. For a Unitree H2, see the \u003ca href=\"\/en\/products\/brainco-revo-2-tactile-dexterous-hand-for-h2\"\u003eRevo 2 tactile hand configured for the H2\u003c\/a\u003e; for other makes and models, compare our full range of \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTouch in every fingertip:\u003c\/strong\u003e Capacitive sensors in all five fingertips read pressure, friction, force direction and proximity, with normal and tangential force measured up to 25 N.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e383 g at human-hand size:\u003c\/strong\u003e The hand is 160 mm from palm base to middle fingertip and 78.5 mm across the palm, which keeps the load on a humanoid's arm low.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e11 degrees of freedom from six motors:\u003c\/strong\u003e Six motors drive two thumb joints and one joint in each finger, five more joints are passive, and control repeats to 0.1°.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e50 N grip, 20 kg payload:\u003c\/strong\u003e The five-finger grip reaches at least 50 N, the pinch at least 15 N, and the hand carries at least 20 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTactile adaptive control:\u003c\/strong\u003e On top of position, velocity and current control, the Touch adjusts finger current from what the fingertips feel, so soft and rigid objects get the grip they need.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT at up to 1 kHz:\u003c\/strong\u003e RS-485 and CAN FD run at up to 500 Hz and EtherCAT (CoE and PDO) at up to 1 kHz, from a 12–64 V supply.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePython, C\/C++ and ROS:\u003c\/strong\u003e BrainCo's SDKs run on Linux, Windows and ROS, and the firmware updates over the air.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"BrainCo","offers":[{"title":"Default Title","offer_id":67633064771814,"sku":"BrainCo-Revo-2-Touch-Left","price":21900.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/brainco-revo-2-silver-r_1.jpg?v=1791277767"},{"product_id":"brainco-revo-2-touch-biomimetic-dexterous-right-hand","title":"BrainCo Revo 2 Touch Bionic Hand Right (XTR)","description":"\u003cp\u003eThe BrainCo Revo 2 Touch Right (XTR) is a bionic dexterous robotic hand for the right side of a humanoid robot or for a single robot arm, with a capacitive tactile sensor in every fingertip. It packs 11 degrees of freedom, six of them motor-driven, into 383 g, 160 mm from palm base to middle fingertip and 78.5 mm across the palm.\u003c\/p\u003e\u003cp\u003eEach fingertip sensor collects six channels and reports pressure, friction, force direction and proximity: normal and tangential force up to 25 N at 0.1 N resolution, and an approaching object up to 1 cm away, sampled at 70 Hz. In tactile adaptive control the hand sets finger current from those readings, so it closes firmly on a bottle and gently on a paper cup. BrainCo's open Python grasping example detects contact and estimates object stiffness from the same data, pinching a foam block with two fingers, holding a paper cup with three and gripping a water bottle with five, a ready starting point for grasp learning, teleoperation and contact-rich manipulation research.\u003c\/p\u003e\u003cp\u003eUnder the sensors the Touch is the same mechanism as the rest of the Revo 2 line: at least 50 N grip, 15 N pinch, a 20 kg payload, 0.1° repeat precision and a full flex in 0.65 s or less. The \u003ca href=\"\/en\/products\/brainco-revo-2-basic-right-dexterous-bionic-hand-xrr\"\u003eRevo 2 Basic right hand (XRR)\u003c\/a\u003e runs RS-485 or CAN FD on 12–28 V, the \u003ca href=\"\/en\/products\/brainco-revo-2-pro-dexterous-right-hand-xer\"\u003eRevo 2 Pro right hand (XER)\u003c\/a\u003e adds EtherCAT and a 12–64 V input, and the Touch keeps the Pro's interfaces and adds the fingertip sensing.\u003c\/p\u003e\u003cp\u003eIts default device ID is 127, so it shares a bus with the \u003ca href=\"\/en\/products\/brainco-revo-2-touch-biomimetic-dexterous-left-hand\"\u003eRevo 2 Touch left hand (XTL)\u003c\/a\u003e, which is set to 126, without re-addressing. Control runs at up to 1 kHz over EtherCAT and 500 Hz over RS-485 or CAN FD, from BrainCo's Python and C\/C++ SDKs on Linux, Windows and ROS, with URDF and MuJoCo models for simulation. The box holds the hand with its RS-485\/CAN FD, EtherCAT and power cables. For a Unitree H2 there is a \u003ca href=\"\/en\/products\/brainco-revo-2-tactile-dexterous-hand-for-h2\"\u003eRevo 2 tactile hand configured for the H2\u003c\/a\u003e, and the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e cover other makers and designs.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFingertips that feel:\u003c\/strong\u003e Each of the five fingertips carries a capacitive sensor that reads pressure, friction, force direction and proximity, resolving 0.1 N up to 25 N.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrip set by touch:\u003c\/strong\u003e Tactile adaptive control sets finger current from the fingertip readings, so a paper cup and a water bottle each get the force they need.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSenses before contact:\u003c\/strong\u003e The proximity channel notices an object up to 1 cm from a fingertip, and the tactile data is sampled at 70 Hz.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e383 g, 20 kg payload:\u003c\/strong\u003e The right hand weighs 383 g yet carries at least 20 kg, with at least 50 N five-finger grip and 15 N pinch.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1 kHz over EtherCAT:\u003c\/strong\u003e EtherCAT with CoE and PDO runs at up to 1 kHz, RS-485 and CAN FD at up to 500 Hz, on any supply from 12 to 64 V.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReady for ROS and simulation:\u003c\/strong\u003e Python and C\/C++ SDKs run on Linux, Windows and ROS, with URDF and MuJoCo models and over-the-air firmware updates.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"BrainCo","offers":[{"title":"Default Title","offer_id":67633064935654,"sku":"BrainCo-Revo-2-Touch","price":21900.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/brainco-revo-2-silver-r.jpg?v=1791277767"},{"product_id":"shadow-dex-ee-dexterous-hand-robotic-research-platform","title":"Shadow DEX-EE Three-Finger Dexterous Hand","description":"\u003cp\u003eThe Shadow DEX-EE is a three-finger dexterous robotic hand from Shadow Robot Company, developed in collaboration with Google DeepMind for machine-learning research. It is built to keep running through the trial-and-error phase of machine learning, when an untrained policy drives the hand into repeated impacts, high forces and abrasion. Each of its three fingers is a self-contained module with four joints, 12 degrees of freedom in all, and a damaged finger comes off with six screws and one connector while it goes for repair.\u003c\/p\u003e\u003cp\u003eDEX-EE is aimed at labs running reinforcement learning, imitation learning and autonomous grasping on real hardware, where uptime matters more than human proportions: at 350 mm long, 165 × 160 mm across and 4.1 kg, it is larger than a human hand. Five motors in each finger base drive the four joints through tendons in an N+1 arrangement, each closing a 10 kHz force loop for active compliance, and the host runs joint position or torque control at 1 kHz. Joints move at up to 180°\/s and each fingertip presses with at least 8 N.\u003c\/p\u003e\u003cp\u003eEvery finger carries 155 sensor channels: four joint sensors at 0.022°, a 3-axis accelerometer and gyroscope, five tendon force sensors at 4 mN, and motor velocity, current, temperature and clutch-slip readings, all at 1,000 Hz. The fingertip is a camera-based tactile sensor in which a stereo pair watches about 500 markers inside the silicone skin and streams 1280 × 480 video at 50 fps, with all three fingertips sharing one USB 3.0 link. Optional modules add 14 and 22 three-axis taxels on the middle and proximal phalanges. Motor temperature reduces power gradually instead of cutting out, and tendon odometry shows when a tendon is due for replacement.\u003c\/p\u003e\u003cp\u003eThe standard DEX-EE spaces its fingers evenly around the base; the DEX-EE Chiral offsets the third finger like a thumb for teleoperation and bimanual work, as a left hand, a right hand or a pair, and the configuration is confirmed with the quotation. The hand mounts on an ISO 9409-1-50-4-M6 flange, connects over EtherCAT with full ROS integration and runs from a 48 V, 200 W supply. For human-like kinematics with five fingers, see the \u003ca href=\"\/en\/products\/shadow-dexterous-hand-dh-five-finger-robotic-hand\"\u003eShadow Dexterous Hand (DH)\u003c\/a\u003e, or compare our full range of \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFingers you can swap:\u003c\/strong\u003e Each finger is a self-contained module held by six screws and one connector, so a damaged finger is replaced while it goes for repair.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuilt to survive untrained policies:\u003c\/strong\u003e Shadow designed DEX-EE to withstand repeated impacts, high forces and abrasion from untrained neural networks, with a long mean time between failures and a short repair time.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCamera-based tactile fingertips:\u003c\/strong\u003e A stereo camera pair tracks about 500 markers inside each fingertip's silicone skin and streams 1280 × 480 video at 50 fps.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e155 sensor channels per finger:\u003c\/strong\u003e Joint angles at 0.022°, tendon forces at 4 mN, acceleration, angular rate and motor health all report at 1,000 Hz.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eN+1 tendon drive at 10 kHz:\u003c\/strong\u003e Five motors drive each finger's four joints, and each motor closes a 10 kHz force loop for active compliance.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e180°\/s joints, 8 N fingertips:\u003c\/strong\u003e Each of the 12 joints moves at up to 180°\/s, and each fingertip presses with at least 8 N.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT, ROS and an ISO flange:\u003c\/strong\u003e The hand connects over EtherCAT with full ROS integration and mounts with four M6 screws on an ISO 9409-1-50-4-M6 pattern.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Shadow","offers":[{"title":"Default Title","offer_id":67633066049766,"sku":"Shadow-DEX-EE","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/logo-shadow-2.jpg?v=1791277769"},{"product_id":"shadow-dexterous-hand-extra-lite-dhel-three-digit-research-hand","title":"Shadow Dexterous Hand Extra Lite (DHEL) Three-Finger Hand","description":"\u003cp\u003eThe Shadow Dexterous Hand Extra Lite (DHEL) is a three-digit dexterous robotic hand from Shadow Robot Company, two fingers and a thumb, and a reduced configuration of the Shadow Dexterous Hand Lite. It has 10 degrees of freedom over 12 joints, driven by 10 DC motors through tendons, weighs 2.1 kg and holds up to 3 kg in a power grasp.\u003c\/p\u003e\u003cp\u003eIt is built for labs that want Shadow's finger design at a lower mass and with fewer channels to control: arms with a smaller payload, mobile manipulators and grasping experiments that three digits can handle. The thumb and both fingers keep the four-joint layout of the full hand, while ten motors instead of twenty give reinforcement and imitation learning a smaller action space to work in.\u003c\/p\u003e\u003cp\u003eOn board are 20 tendon load sensors, an IMU, Hall-effect joint sensing and one Shadow Tactile Fingertip with 17 three-axis taxels; up to three can be fitted, one per digit. Control runs at 1 kHz through the host over EtherCAT, and the hand works inside Shadow's open-source ROS platform like every hand in the series.\u003c\/p\u003e\u003cp\u003eOne size up, the \u003ca href=\"\/en\/products\/shadow-dexterous-hand-lite-dhl-five-finger-robotic-hand\"\u003eShadow Dexterous Hand Lite (DHL)\u003c\/a\u003e adds a third finger for 13 degrees of freedom at 2.4 kg, and the \u003ca href=\"\/en\/products\/shadow-dexterous-hand-dh-five-finger-robotic-hand\"\u003efive-finger Shadow Dexterous Hand (DH)\u003c\/a\u003e has 24 joints with a wrist. The \u003ca href=\"\/en\/products\/shadow-dexterous-hand-extra-super-lite-dhsl-reduced-finger-research-hand\"\u003eShadow Dexterous Hand Extra Super Lite (DHSL)\u003c\/a\u003e is smaller still, with one finger and a thumb. Compare them with the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo fingers and a thumb:\u003c\/strong\u003e The Extra Lite keeps the thumb and two fingers of the Shadow Hand, each with the same four-joint layout as on the full hand.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e10 degrees of freedom, 10 motors:\u003c\/strong\u003e Ten DC motors drive 12 joints through tendons, one motor for each degree of freedom.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e2.1 kg with a 3 kg payload:\u003c\/strong\u003e It weighs 2.1 kg and holds up to 3 kg in a power grasp, which leaves more of a small arm's payload for the object.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTactile fingertip as standard:\u003c\/strong\u003e One Shadow Tactile Fingertip with 17 three-axis taxels comes fitted, and each of the three digits can carry one.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e20 tendon load sensors and an IMU:\u003c\/strong\u003e Tendon forces and the hand's motion are measured on board for force-aware control and grasp data.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1 kHz EtherCAT with ROS:\u003c\/strong\u003e Control runs at 1 kHz through the host over EtherCAT, inside Shadow's open-source ROS platform.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Shadow","offers":[{"title":"Default Title","offer_id":67633066180838,"sku":"Shadow-DHEL","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/shadow-robot_1_2.jpg?v=1791277769"},{"product_id":"dexrobot-dexhand-021-concept-intelligent-dexterous-hand","title":"DexRobot DexHand021 Concept Dexterous Hand","description":"\u003cp\u003eThe DexRobot DexHand021 Concept is the concept version of DexRobot's DexHand021 five-finger dexterous robotic hand, built as an open, multimodal platform for humanoid and robot-arm research. It has 18 degrees of freedom across a thumb and four fingers and five types of built-in sensing, with actuation, sensing and control packed inside the hand itself — what DexRobot calls an all-in-one hand.\u003c\/p\u003e\u003cp\u003eTwo design choices matter for a lab that runs a hand every day. Each finger is a separate module that is replaced on its own, so a damaged finger is a short repair rather than a returned hand. Holding a posture takes no power, so a static grasp does not drain a mobile robot's battery during long holds.\u003c\/p\u003e\u003cp\u003eDexRobot designed the hand to work with mainstream robot protocols and data formats, so it can sit on an existing arm or humanoid without custom bridging. Weight, fingertip force, interface, supply voltage and hand side for your setup are confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eWithin the range, the \u003ca href=\"\/en\/products\/dexrobot-021mp-intelligent-dexterous-hand\"\u003eDexHand021 MP\u003c\/a\u003e is the production five-finger hand with 19 degrees of freedom, tactile and proximity sensing and CAN FD control; the \u003ca href=\"\/en\/products\/dexrobot-021pro-wrist-hand-integrated-dexterous-hand\"\u003eDexHand021 Pro\u003c\/a\u003e adds an integrated wrist, 22 degrees of freedom and a palm camera; and the \u003ca href=\"\/en\/products\/dexrobot-021s-three-fingered-dexterous-hand\"\u003eDexHand021 S\u003c\/a\u003e is a 0.6 kg three-finger hand with 8 degrees of freedom. Compare them with the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e18 degrees of freedom:\u003c\/strong\u003e Eighteen degrees of freedom across a thumb and four fingers cover power grasps, pinches and finger-by-finger postures.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFive sensing types:\u003c\/strong\u003e DexRobot builds five types of sensing into the hand, so a controller can close the loop on contact rather than on finger position alone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFingers replaced one at a time:\u003c\/strong\u003e Each finger comes out as its own module, so a damaged finger is swapped without taking the whole hand apart.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eZero-power posture hold:\u003c\/strong\u003e Holding a posture draws no power, which saves energy during long static grasps on battery-powered robots.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAll in one hand:\u003c\/strong\u003e Actuation, sensing and control sit inside the hand, which keeps external wiring on the robot arm to a minimum.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommon protocols and data formats:\u003c\/strong\u003e DexRobot designed the hand to work with the protocols and data formats most robots already use, which shortens integration on an existing arm.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"DexRobot","offers":[{"title":"Default Title","offer_id":67633066344678,"sku":"DexRobot-021-Concept","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/dexhand021_concept_1.jpg?v=1791277769"},{"product_id":"dexrobot-021mp-intelligent-dexterous-hand","title":"DexRobot DexHand021 MP Dexterous Hand","description":"\u003cp\u003eThe DexRobot DexHand021 MP is the production version of DexRobot's DexHand021 five-finger dexterous robotic hand. It has 19 degrees of freedom, 12 of them driven by motors through tendons and 7 passive, and weighs 1 kg at 292.6 × 113.2 × 56.5 mm. DexRobot rates it for more than 15 human-like grasps, including cylindrical, spherical and multi-finger pinch grips, and for more than 1,000,000 cycles.\u003c\/p\u003e\u003cp\u003eSensing is what sets it apart from a position-only hand. The fingers read normal force from 0 to 20 N at 0.1 N resolution and ±2 % full-scale accuracy, tangential force at 0.25 N with 45° direction resolution, proximity from 1 cm and temperature, all sampled at 50 Hz or faster. A controller can feel first contact, track sideways force and set the grip from what the fingers report, which is what grasp-learning, teleoperation and humanoid manipulation projects need.\u003c\/p\u003e\u003cp\u003eEach fingertip pushes with at least 12 N, the grasp reaches at least 38 N and the hand carries 5 kg in total. Fingers repeat to ±0.15 mm, close on objects from 10 mm across and complete a cycle in under a second. One GX12 connector carries the DC 24 V supply and CAN FD; the hand draws 0.2 A at rest and up to 7.4 A. Control runs in position, trajectory or force mode through an open low-level API with Python, C++, ROS1, ROS2 and micro-ROS, and DexRobot adds hand models, physics simulation, motion mapping, teleoperation and reinforcement and imitation learning tools, with motion capture, VR and camera gesture input.\u003c\/p\u003e\u003cp\u003eWithin the DexHand021 range, the \u003ca href=\"\/en\/products\/dexrobot-021pro-wrist-hand-integrated-dexterous-hand\"\u003eDexHand021 Pro\u003c\/a\u003e adds an integrated wrist, 22 degrees of freedom, 400+ tactile sensing units and a palm camera; the \u003ca href=\"\/en\/products\/dexrobot-021s-three-fingered-dexterous-hand\"\u003eDexHand021 S\u003c\/a\u003e is a 0.6 kg three-finger hand with 8 degrees of freedom; and the \u003ca href=\"\/en\/products\/dexrobot-dexhand-021-concept-intelligent-dexterous-hand\"\u003eDexHand021 Concept\u003c\/a\u003e is the 18-degree-of-freedom concept version. See all our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e to compare other makers.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTactile, force and proximity sensing:\u003c\/strong\u003e The fingers read normal force from 0 to 20 N at 0.1 N resolution, tangential force at 0.25 N, proximity from 1 cm and temperature, sampled at 50 Hz or faster.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e19 degrees of freedom on 12 drives:\u003c\/strong\u003e Twelve motor-driven joints and seven passive ones, moved through tendons, cover more than 15 human grasps, including cylindrical, spherical and multi-finger pinch grips.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e12 N fingertips, 5 kg hand load:\u003c\/strong\u003e Each fingertip pushes with at least 12 N, the grasp reaches at least 38 N, and the hand carries a total load of 5 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e±0.15 mm repeatability:\u003c\/strong\u003e Fingers return to position within ±0.15 mm, close on objects from 10 mm across and complete a cycle in under a second.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRated beyond a million cycles:\u003c\/strong\u003e DexRobot rates the hand for more than 1,000,000 cycles, which suits teleoperation and data-collection work that runs all day.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCAN FD on 24 V:\u003c\/strong\u003e One GX12 connector carries the 24 V supply and CAN FD, with the hand drawing 0.2 A at rest and up to 7.4 A.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePython, C++ and ROS:\u003c\/strong\u003e An open low-level API, Python and C++ support and ROS1, ROS2 and micro-ROS integration come with simulation models and teleoperation and learning tools.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"DexRobot","offers":[{"title":"Default Title","offer_id":67633066410214,"sku":"DexRobot-021MP","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/dexhand021_mp.jpg?v=1791277769"},{"product_id":"dexrobot-021pro-wrist-hand-integrated-dexterous-hand","title":"DexRobot DexHand021 Pro Wrist-Hand Dexterous Hand","description":"\u003cp\u003eThe DexRobot DexHand021 Pro is DexRobot's flagship five-finger dexterous robotic hand with the wrist built in. It has 22 degrees of freedom: 16 active and 4 passive finger joints plus two wrist joints, 18 of them active in all, moved by a dual-tendon omnidirectional drive. DexRobot rates its payload at 50 N, its operational precision at sub-millimetre level and its durability at more than 300,000 test cycles.\u003c\/p\u003e\u003cp\u003eIt is built for teams whose manipulation work depends on what the hand perceives. More than 400 tactile sensing units cover the palm and fingers, 20 high-precision sensors track joint positions and a 5 MP RGB camera looks out from the palm, giving over 500 physical sensing points plus real-time motor feedback. Hybrid position and force control uses that data together with the natural compliance of the tendons, which suits embodied-AI skill learning, teleoperation and contact-rich grasping on humanoid robots.\u003c\/p\u003e\u003cp\u003eThe wrist joints are driven by linear push rods and tilt the hand front-to-back and side-to-side, so one unit gives the robot both the wrist and the hand. DexRobot supplies Python and C++ SDKs, URDF models, kinematic libraries and simulation examples. Weight, supply voltage, communication interface and mounting for your robot are confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eThe \u003ca href=\"\/en\/products\/dexrobot-021mp-intelligent-dexterous-hand\"\u003eDexHand021 MP\u003c\/a\u003e is the five-finger production hand without the wrist, with 19 degrees of freedom and fingertip tactile sensing; the \u003ca href=\"\/en\/products\/dexrobot-021s-three-fingered-dexterous-hand\"\u003eDexHand021 S\u003c\/a\u003e is a 0.6 kg three-finger hand; and the \u003ca href=\"\/en\/products\/dexrobot-dexhand-021-concept-intelligent-dexterous-hand\"\u003eDexHand021 Concept\u003c\/a\u003e is the 18-degree-of-freedom concept version. Compare them with the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eWrist built into the hand:\u003c\/strong\u003e Two wrist joints, driven by linear push rods, tilt the hand front-to-back and side-to-side as part of the same unit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e22 degrees of freedom, 18 active:\u003c\/strong\u003e Sixteen active and four passive finger joints plus the two wrist joints give the hand opposable motion through the full 3D workspace.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e400+ tactile units and a palm camera:\u003c\/strong\u003e More than 400 tactile sensing units, 20 joint position sensors and a 5 MP RGB camera in the palm add up to over 500 sensing points on one hand.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual-tendon drive:\u003c\/strong\u003e The dual-tendon omnidirectional drive gives the fingers built-in compliance, and DexRobot's hybrid position and force control works with it for sub-millimetre operational precision.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e50 N payload, 300,000 cycles:\u003c\/strong\u003e DexRobot rates the payload at 50 N and has tested the hand for more than 300,000 cycles.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSDKs, URDF and simulation:\u003c\/strong\u003e Python and C++ SDKs, URDF models, kinematic libraries and simulation examples bring the hand into a team's own training and control stack.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"DexRobot","offers":[{"title":"Default Title","offer_id":67633066475750,"sku":"DexRobot-021PRO","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/dexhand021_pro.jpg?v=1791277769"},{"product_id":"dexrobot-021s-three-fingered-dexterous-hand","title":"DexRobot DexHand021 S Three-Finger Dexterous Hand","description":"\u003cp\u003eThe DexRobot DexHand021 S is a three-finger dexterous robotic hand for robot arms, research benches and teaching labs. It has 8 degrees of freedom, weighs 0.6 kg and measures 208 × 80 × 82.8 mm, and DexRobot designed it to cover about 80 % of what a five-finger hand does at a cost-effective price.\u003c\/p\u003e\u003cp\u003eA gear, tendon and linkage transmission gives the same fingers at least 20 N at the fingertip, 45 N at the finger pad and 100 N at the finger root. Three fingers lift 2.5 kg palm down at rated load and 5 kg at maximum, repeat to ±0.5 mm and grasp objects 30 mm across or smaller. Torque adjusts steplessly from 0 to 1 A, so the hand adapts to spheres and irregular objects and can screw, plug and unplug parts.\u003c\/p\u003e\u003cp\u003eJoint position sensing and a 5 MP palm camera (30 fps, 76° field of view, objects from 6 cm) are standard, and the camera supports visual-servo grasping. Capacitive tactile sensing is an option: normal force from 0 to 20 N at 0.1 N resolution and ±2 % full-scale accuracy, tangential force at 0.25 N with 45° direction resolution and proximity from 1 cm, sampled at 50 Hz or faster. The hand runs on DC 24 V (0.13 A at rest, 2 A maximum), connects over CAN FD or RS485, comes with an open-source SDK and is rated for 200,000 cycles. DexRobot names research, education and maker projects, interactive robots and industrial and agricultural work such as fruit and vegetable picking among its uses.\u003c\/p\u003e\u003cp\u003eFor five fingers, the \u003ca href=\"\/en\/products\/dexrobot-021mp-intelligent-dexterous-hand\"\u003eDexHand021 MP\u003c\/a\u003e has 19 degrees of freedom, fingertip tactile sensing and a 5 kg hand load, and the \u003ca href=\"\/en\/products\/dexrobot-021pro-wrist-hand-integrated-dexterous-hand\"\u003eDexHand021 Pro\u003c\/a\u003e adds an integrated wrist and 22 degrees of freedom. Browse our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e for other three- and five-finger designs.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree fingers, 8 degrees of freedom:\u003c\/strong\u003e DexRobot designed the 021 S to cover about 80 % of what a five-finger hand does, from spheres and irregular objects to screwing, plugging and unplugging.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.6 kg on the arm:\u003c\/strong\u003e At 0.6 kg and 208 × 80 × 82.8 mm, the hand adds little weight to the end of a collaborative arm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGear, tendon and linkage drive:\u003c\/strong\u003e Three transmissions work together to give at least 20 N at the fingertip, 45 N at the finger pad and 100 N at the finger root.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e2.5 kg rated, 5 kg maximum:\u003c\/strong\u003e Three fingers lift 2.5 kg palm down at rated load and up to 5 kg at maximum, repeating to ±0.5 mm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePalm camera for visual servoing:\u003c\/strong\u003e A 5 MP palm camera at 30 fps with a 76° field of view guides visual-servo grasping, alongside joint position sensing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOptional tactile fingertips:\u003c\/strong\u003e Capacitive sensing adds normal force from 0 to 20 N at 0.1 N resolution, tangential force and proximity from 1 cm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCAN FD or RS485, open SDK:\u003c\/strong\u003e The hand runs on DC 24 V, connects over CAN FD or RS485 and comes with an open-source SDK for your own control code.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"DexRobot","offers":[{"title":"Default Title","offer_id":67633066574054,"sku":"DexRobot-021S","price":7250.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/dexrobot.jpg?v=1791277769"},{"product_id":"linkerbot-linker-hand-o6-dexterous-robotic-hand","title":"Linkerbot Linker Hand O6 Dexterous Hand","description":"\u003cp\u003eThe Linkerbot Linker Hand O6 is a five-finger dexterous robotic hand that weighs 360 g, made in left- and right-hand versions. It has six active joints and five passive ones: motors drive thumb flexion, thumb abduction\/adduction and the flexion of each finger, and the passive joints let the fingers wrap around irregular objects. Linkerbot designed it to bring a multi-finger hand to everyday robot projects.\u003c\/p\u003e\u003cp\u003eThe light aerospace-grade aluminium frame sits on high-torque servo modules with worm gears, and Linkerbot rates the hand at a 50 kg maximum load. The five fingers grip with up to 70 N, each fingertip pushes with 25 N and the thumb with 20 N, and positions repeat to ±0.20 mm under hybrid force-position control. It suits humanoid robots, cobot arms in logistics handling and assembly, and research groups that need a hand for grasping irregular objects without the weight of a high-DoF hand.\u003c\/p\u003e\u003cp\u003eThe O6 is made with CAN, CAN FD, RS-485 or EtherCAT and runs on 24–48 V. Linkerbot's host software for Windows and Ubuntu moves each joint from a slider, and its Python, ROS and ROS 2 SDKs drive one hand or a left and right pair, with optional fingertip pressure sensors. It comes in seven colours, from pearl white to obsidian black.\u003c\/p\u003e\u003cp\u003eWithin the Linker Hand range, the \u003ca href=\"\/en\/products\/linkerbot-linker-hand-o7-dexterous-robotic-hand\"\u003eLinker Hand O7\u003c\/a\u003e adds a seventh active joint and a built-in 72-cell tactile array, and the \u003ca href=\"\/en\/products\/linkerbot-linker-hand-l10-standard-version\"\u003eLinker Hand L10 Standard\u003c\/a\u003e moves ten joints, including side-to-side finger movement. For 16 active joints, see the \u003ca href=\"\/en\/products\/linkerbot-linker-hand-l20-pro-version\"\u003eLinker Hand L20 Pro\u003c\/a\u003e, or compare all our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e360 g, 50 kg maximum load:\u003c\/strong\u003e An aerospace-grade aluminium frame keeps the hand at 360 g, and Linkerbot rates its maximum load at 50 kg, so it adds little weight to a cobot wrist or a humanoid arm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e70 N five-finger grip:\u003c\/strong\u003e The five fingers close with up to 70 N together, each of the four fingertips pushes with 25 N and the thumb with 20 N.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e6 active and 5 passive joints:\u003c\/strong\u003e Six motors drive thumb flexion, thumb abduction and the flexion of each finger, while five passive joints let the fingers curl around irregular shapes.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorm-gear servo modules:\u003c\/strong\u003e The linkage fingers run on high-torque servo modules with worm gears under hybrid force-position control, repeating to ±0.20 mm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFour bus options:\u003c\/strong\u003e The O6 is made with CAN, CAN FD, RS-485 or EtherCAT and runs on a 24–48 V supply.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePython, ROS and ROS 2:\u003c\/strong\u003e Linkerbot's SDKs drive a single O6 or a left and right pair, alongside host software for Windows and Ubuntu.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOptional fingertip sensing:\u003c\/strong\u003e Fingertip pressure sensors can be fitted, and their readings arrive through the same SDK for force-aware grasping.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Linkerbot","offers":[{"title":"Default Title","offer_id":67633070506214,"sku":"Linkerbot-Linker-Hand-06","price":8600.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/linkerbot-linker-hand-06.jpg?v=1791277774"},{"product_id":"linkerbot-linker-hand-o7-dexterous-robotic-hand","title":"Linkerbot Linker Hand O7 Dexterous Hand","description":"\u003cp\u003eThe Linkerbot Linker Hand O7 is a palm-sized dexterous robotic hand with a tactile array built into the hand, for robots that need to feel what they pick up. It combines 7 active joints with 10 passive ones, 17 degrees of freedom in all, in an aluminium-alloy frame of about 700 g, and is made as a left or a right hand.\u003c\/p\u003e\u003cp\u003eThe 72-cell resistive array (6 × 12) reports where and how hard the hand touches an object at 200 frames per second, so a controller sees contact, pressure distribution and the start of a slip. That makes the O7 a fit for contact-rich manipulation research, imitation-learning data collection and humanoid robots that handle objects of varying shape. The passive joints help as well: they let the fingers settle around an object whose pose or friction is uncertain.\u003c\/p\u003e\u003cp\u003eThe fingers run on Linkerbot's own joint modules through a linkage drive and repeat to ±0.20 mm. The thumb swings through 95°, the fingers flex through 90°, thumb and fingers pinch with 12 N, and the hand carries up to 5 kg. It connects over CAN or RS-485, works with Linkerbot's ROS 2 SDK and URDF model, and protects itself against overload and overheating.\u003c\/p\u003e\u003cp\u003eNext to it in the range, the \u003ca href=\"\/en\/products\/linkerbot-linker-hand-o6-dexterous-robotic-hand\"\u003eLinker Hand O6\u003c\/a\u003e is lighter at 360 g with six active joints and optional fingertip sensors, and the \u003ca href=\"\/en\/products\/linkerbot-linker-hand-l10-standard-version\"\u003eLinker Hand L10 Standard\u003c\/a\u003e adds side-to-side finger movement with ten active joints. Compare them with the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e72-cell tactile array built in:\u003c\/strong\u003e A 6 × 12 resistive array maps contact location and pressure at 200 frames per second, with no add-on sensor kit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e7 active, 10 passive joints:\u003c\/strong\u003e Seven driven joints set the grasp, and ten passive joints let the fingers settle around an object whose position or shape is uncertain.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e95° thumb yaw:\u003c\/strong\u003e The thumb swings through 95° and the fingers flex through 90°, enough for opposed pinches as well as wrap grasps.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e12 N pinch, 5 kg payload:\u003c\/strong\u003e Thumb and fingers pinch with 12 N, and the hand carries up to 5 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e±0.20 mm repeatability:\u003c\/strong\u003e Linkage fingers on Linkerbot's own joint modules return to the same position within ±0.20 mm, in an aluminium-alloy frame of about 700 g.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eROS 2 and URDF:\u003c\/strong\u003e The O7 talks CAN or RS-485, Linkerbot's ROS 2 SDK drives it, and a URDF model covers simulation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOverload and thermal protection:\u003c\/strong\u003e The hand protects itself against overload and overheating during jams and long data-collection runs.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Linkerbot","offers":[{"title":"Default Title","offer_id":67633070571750,"sku":"Linkerbot-Linker-Hand-07","price":10050.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/linkerbot_2.jpg?v=1791277774"},{"product_id":"linkerbot-linker-hand-j42-industrial-grade-6-finger-claw","title":"Linkerbot Linker Hand J42 Six-Finger Dexterous Hand","description":"\u003cp\u003eThe Linkerbot Linker Hand J42 is a six-finger dexterous robotic hand in an industrial-grade claw layout, with up to 42 degrees of freedom driven by tendons (cables). It is built as an end effector for automation cells, mobile manipulators and humanoid platforms that have to grasp and reorient parts a two-finger gripper cannot hold.\u003c\/p\u003e\u003cp\u003eThe sixth finger is the point of the design. With one more contact point than a human hand, the J42 can hold an irregular part with several fingers while others turn or reposition it, wrap around soft packaging, or steady a part during assembly. The tendon drive routes the motor force through the hand, so the fingers stay light and give slightly on contact with a part or a fixture.\u003c\/p\u003e\u003cp\u003eIt is aimed at manufacturing engineers and research teams working on in-hand manipulation and multi-finger grasping, where joint count and contact redundancy matter more than a human-like shape. Weight, payload, finger force, the control interface, sensors and software support are specified for your robot and confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eFor a five-finger tendon-driven hand, see the \u003ca href=\"\/en\/products\/linkerbot-linker-hand-l30-cable-driven-version\"\u003eLinker Hand L30 Cable-Driven\u003c\/a\u003e; for a linkage hand with 16 active joints, the \u003ca href=\"\/en\/products\/linkerbot-linker-hand-l20-pro-version\"\u003eLinker Hand L20 Pro\u003c\/a\u003e. Compare the whole range of \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSix fingers instead of five:\u003c\/strong\u003e A sixth finger adds a contact point, so the hand can hold a part with some fingers while others reposition it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp to 42 degrees of freedom:\u003c\/strong\u003e The J42 has the highest joint count in the Linker Hand range, for in-hand reorientation and postures a parallel gripper cannot reach.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTendon (cable) drive:\u003c\/strong\u003e Cables route the motor force through the hand, which keeps the fingers light and lets them give on contact with a part or a fixture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIndustrial claw layout:\u003c\/strong\u003e Linkerbot built the J42 as an industrial-grade end effector for automation cells, mobile manipulators and humanoid platforms.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpecified per project:\u003c\/strong\u003e Sensors, control electronics and the interface to your robot are agreed with the quotation, so the hand is configured for your cell before the order.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Linkerbot","offers":[{"title":"Default Title","offer_id":67633070637286,"sku":"Linkerbot-Linker-Hand-J42","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/linkerbot-linker-hand-j42.jpg?v=1791277773"},{"product_id":"linkerbot-linker-hand-l10-standard-version","title":"Linkerbot Linker Hand L10 Standard Dexterous Hand","description":"\u003cp\u003eThe Linkerbot Linker Hand L10 Standard is a linkage-driven dexterous robotic hand with 10 active and 10 passive degrees of freedom, built for manipulation research, humanoid robots and flexible automation. It weighs about 750 g in an aluminium-alloy frame and is made as a left or a right hand.\u003c\/p\u003e\u003cp\u003eWhat sets the L10 apart in the Linker Hand range is where its ten motors go. Three drive the thumb (base pitch, abduction and rotation), four bend the base of each finger, and three move the index, ring and little fingers sideways, so the hand can spread its fingers around a wide object or hold a tool handle in a human grip. Ten passive joints let the fingers follow the shape of what they hold without a command for every contact.\u003c\/p\u003e\u003cp\u003eLinkerbot's own motor modules drive the fingers through linkages, which keeps the motion robust and repeatable to ±0.20 mm. The hand carries up to 5 kg and pinches with 12 N. It connects over EtherCAT or CAN bus, and the SDK also handles RS-485 (Modbus). Linkerbot's Python, ROS 1 and ROS 2 SDKs include a GUI with a slider per joint, motion recording and replay, useful for teams collecting demonstration data. Force sensing, a 72-cell resistive tactile array or electronic skin can be specified for contact-rich work.\u003c\/p\u003e\u003cp\u003eFor more dexterity, the \u003ca href=\"\/en\/products\/linkerbot-linker-hand-l20-pro-version\"\u003eLinker Hand L20 Pro\u003c\/a\u003e drives 16 joints including the fingertips; for a lighter hand with tactile sensing built in, see the \u003ca href=\"\/en\/products\/linkerbot-linker-hand-o7-dexterous-robotic-hand\"\u003eLinker Hand O7\u003c\/a\u003e. Compare them with all our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e10 active, 10 passive joints:\u003c\/strong\u003e Ten motors drive the thumb in three axes, the base of each finger and the sideways spread of three fingers, and ten passive joints follow them.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFingers that spread:\u003c\/strong\u003e The index, ring and little fingers move sideways under motor control, so the hand can widen a grasp or hold a tool handle the way a person does.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e750 g, 5 kg payload:\u003c\/strong\u003e The aluminium-alloy hand weighs about 750 g, carries up to 5 kg and pinches with 12 N.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLinkage drive, ±0.20 mm:\u003c\/strong\u003e Linkerbot's own motor modules move the fingers through linkages, which keeps the motion robust and repeatable to ±0.20 mm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT or CAN:\u003c\/strong\u003e EtherCAT suits real-time control inside a larger system and CAN suits development work, and Linkerbot's SDK also speaks RS-485 (Modbus).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eROS 1, ROS 2 and Python:\u003c\/strong\u003e Linkerbot's SDKs include a GUI that moves each joint from a slider, records motions and plays them back.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSensing options:\u003c\/strong\u003e Force sensing, a 72-cell resistive tactile array or electronic skin can be specified for contact-rich work and data collection.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Linkerbot","offers":[{"title":"Default Title","offer_id":67633070702822,"sku":"Linkerbot-Linker-Hand-L10","price":20100.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/linkerbot-linker-hand-l10.jpg?v=1791277774"},{"product_id":"linkerbot-linker-hand-l20-pro-version","title":"Linkerbot Linker Hand L20 Pro Dexterous Hand","description":"\u003cp\u003eThe Linkerbot Linker Hand L20 Pro is a five-finger dexterous robotic hand with 21 degrees of freedom, 16 of them motor-driven, built for humanoid robots, cobots and embodied-AI research. Pro marks the full L20: unlike the 10-active-joint L20 Lite, it drives the fingertip joint of every digit as well as the base and sideways movement of each finger. It weighs about 1,200 g and is made as a left or a right hand.\u003c\/p\u003e\u003cp\u003eLinkerbot builds the L20 around its own joint modules, with brushless motors and precision ball screws moving the fingers through linkages under closed-loop position and torque control. The result is a 100 N five-finger grip, 20 N at each fingertip and 15 N at the thumb, a 20 kg rated load and ±0.20 mm repeatability. The fingers bend at 3.5 rad\/s and the thumb swings sideways at 3.2 rad\/s, through 75.78° of thumb rotation and 69.9° of finger bend.\u003c\/p\u003e\u003cp\u003eThe hand connects over CAN or RS-485 and runs on DC 24–48 V, drawing 0.3 A at rest and 1.8 A at most, and Linkerbot rates it for 24-hour continuous operation on 24 V industrial power. Its Windows and Ubuntu host software, Python, ROS and ROS 2 SDKs and URDF model cover teleoperation, imitation learning and simulation, and Linkerbot's grasp-learning tools for the L20 run in Isaac Gym. Linkerbot aims it at research and education, industrial automation, and 3C electronics, automotive and aerospace manufacturing.\u003c\/p\u003e\u003cp\u003eWithin the range, the \u003ca href=\"\/en\/products\/linkerbot-linker-hand-l10-standard-version\"\u003eLinker Hand L10 Standard\u003c\/a\u003e has 10 active joints at about 750 g, and the \u003ca href=\"\/en\/products\/linkerbot-linker-hand-l30-cable-driven-version\"\u003eLinker Hand L30 Cable-Driven\u003c\/a\u003e moves 17 active joints through tendons. Compare all our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e16 active joints, fingertips included:\u003c\/strong\u003e Motors drive the thumb in three axes, the base and sideways spread of every finger and the fingertip joint of all five digits, 21 degrees of freedom in all.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e100 N grip, 20 kg rated load:\u003c\/strong\u003e The five fingers grip with 100 N, each fingertip pushes with 20 N and the thumb with 15 N, and Linkerbot rates the load at 20 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBall-screw joint modules:\u003c\/strong\u003e Brushless motors and precision ball screws in Linkerbot's own joint modules give closed-loop position and torque control that repeats to ±0.20 mm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFast finger motion:\u003c\/strong\u003e The four fingers bend at 3.5 rad\/s (200.47°\/s) and the thumb swings sideways at 3.2 rad\/s (193.59°\/s).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24-hour duty on 24 V:\u003c\/strong\u003e A 0.3 A static current and a DC 24–48 V input let the hand run around the clock on standard industrial power.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePython, ROS 2 and simulation:\u003c\/strong\u003e Linkerbot's Python, ROS and ROS 2 SDKs, a URDF model and its grasp-learning tools for the L20 in Isaac Gym bring the hand into existing robot stacks.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Linkerbot","offers":[{"title":"Default Title","offer_id":67633070768358,"sku":"Linkerbot-Linker-Hand-L20","price":45700.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/linkerbot-linker-hand-l20.jpg?v=1791277773"},{"product_id":"linkerbot-linker-hand-l30-cable-driven-version","title":"Linkerbot Linker Hand L30 Cable-Driven Dexterous Hand","description":"\u003cp\u003eThe Linkerbot Linker Hand L30 Cable-Driven is a tendon-driven five-finger dexterous robotic hand: cables carry the force from its motors to the finger joints, the way tendons work in a human hand. It has 21 joints, 17 of them active and 4 passive, weighs about 1,400 g and is made as a left or a right hand.\u003c\/p\u003e\u003cp\u003eRouting the drive through cables keeps the fingers slim and light and lets them give slightly on contact, which is why tendon hands are chosen for human-like, contact-rich manipulation rather than heavy lifting. The L30 carries up to 5 kg and grips with 12 N. It suits humanoid robot developers and research groups working on biomimetic grasping, in-hand repositioning, tool use and teleoperation, where the number of actively controlled joints matters most.\u003c\/p\u003e\u003cp\u003eControl runs over CAN FD at 500 kbps through a USB-to-CAN FD adapter, on a DC 24 V supply. Linkerbot's L30 ROS 2 SDK for Ubuntu drives one hand or a pair, sets finger speeds and comes with a GUI of preset gestures. Fingertip pressure-matrix sensors are optional; when they are fitted, the SDK publishes the tactile data and the GUI shows each fingertip as a heat map.\u003c\/p\u003e\u003cp\u003eCompare it with the \u003ca href=\"\/en\/products\/linkerbot-linker-hand-l20-pro-version\"\u003eLinker Hand L20 Pro\u003c\/a\u003e, which drives 16 joints through linkages for a 100 N grip, and the six-finger \u003ca href=\"\/en\/products\/linkerbot-linker-hand-j42-industrial-grade-6-finger-claw\"\u003eLinker Hand J42\u003c\/a\u003e, also tendon-driven. The full range is in our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBionic tendon drive:\u003c\/strong\u003e Cables carry the motor force through the hand to the joints, keeping the fingers slim and light and letting them give on contact with an object.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e17 active joints:\u003c\/strong\u003e Seventeen motor-driven joints and four passive ones, 21 in all, give it one more active joint than the L20 Pro.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOptional fingertip tactile matrix:\u003c\/strong\u003e Pressure-matrix sensors can be fitted to the fingertips, and Linkerbot's GUI shows their readings as a heat map and a waveform.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCAN FD at 500 kbps:\u003c\/strong\u003e The hand runs on a DC 24 V supply and connects over CAN FD through a USB-to-CAN FD adapter.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eROS 2 SDK and GUI:\u003c\/strong\u003e Linkerbot's L30 ROS 2 SDK for Ubuntu drives left and right hands, sets finger speeds and includes preset gestures.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e5 kg load, 12 N grip:\u003c\/strong\u003e The hand carries up to 5 kg and grips with 12 N, sized for precise, human-like handling rather than heavy lifting.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Linkerbot","offers":[{"title":"Default Title","offer_id":67633070833894,"sku":"Linkerbot-Linker-Hand-L30","price":91250.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/linkerbot-linker-hand-l30.jpg?v=1791277773"},{"product_id":"paxini-dexh13-dexterous-robotic-hand","title":"Paxini DexH13 Dexterous Robotic Hand","description":"\u003cp\u003eThe Paxini DexH13 is PaXini's second-generation tactile dexterous robotic hand: four fingers with 16 degrees of freedom, 13 of them active, and 1,140 GEN2 ITPU tactile sensing units on the hand. PaXini calls it the first biomimetic dexterous hand to combine multidimensional touch with AI vision, and builds it as a left hand and a right hand.\u003c\/p\u003e\u003cp\u003eVision and touch work as one system. An 8 MP RGB camera in the hand runs PaXini's zero-shot pose estimation to find an object's position and shape before contact, and once the fingers close, 3,420 tactile signals across 15 kinds of tactile perception report contact across the hand. That suits warehouse picking, medical and laboratory handling, industrial manufacturing and service robots, where objects arrive in mixed shapes and orientations.\u003c\/p\u003e\u003cp\u003eThe hand carries 5 kg, pushes with up to 15 N at each fingertip, opens around objects up to 15 cm across and completes an open-close in 1.5 s. Presses position to 1 mm, coreless motors drive the joints, and PaXini rates it for more than 1,000,000 continuous press-and-release cycles. EtherCAT and Modbus connect it to automation controllers; weight, supply voltage and mounting for your robot are confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eThe \u003ca href=\"\/en\/products\/paxini-dexh5-dexterous-robotic-hand\"\u003ePaxini DexH5\u003c\/a\u003e is the lighter four-finger model with 5 active degrees of freedom, 528 tactile units and no camera, and the \u003ca href=\"\/en\/products\/paxini-gmh18-dexterous-robot-hand\"\u003ePaxini GMH18\u003c\/a\u003e is PaXini's five-finger, 18-degree-of-freedom hand with a 20 kg payload and tactile sensors on the fingernails, fingertips, finger pads and palm. Compare all three with the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1,140 tactile units:\u003c\/strong\u003e PaXini's GEN2 ITPU array puts 1,140 multidimensional tactile units on the hand, producing 3,420 tactile signals and 15 kinds of tactile perception.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e8 MP AI hand-eye camera:\u003c\/strong\u003e A camera in the hand runs zero-shot pose estimation to find an object's position and shape before the fingers touch it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e16 degrees of freedom on four fingers:\u003c\/strong\u003e Thirteen active and three passive joints let the four fingers grip, hold, pinch, press and open around an object.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e5 kg payload, 15 N fingertips:\u003c\/strong\u003e The hand carries 5 kg, pushes with up to 15 N at each fingertip and opens around objects up to 15 cm across.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1 mm pressing accuracy:\u003c\/strong\u003e Fingertip presses position to 1 mm, and the hand completes a full open-close in 1.5 s.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRated for a million cycles:\u003c\/strong\u003e PaXini rates the hand for more than 1,000,000 continuous press-and-release cycles.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT and Modbus:\u003c\/strong\u003e Both industrial protocols connect the hand to motion controllers and PLC-based automation cells.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Paxini","offers":[{"title":"Default Title","offer_id":67633071161574,"sku":"Paxini-DexH13","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/paxini_dexh13_dexh13.jpg?v=1791277773"},{"product_id":"paxini-dexh5-dexterous-robotic-hand","title":"Paxini DexH5 Dexterous Robotic Hand","description":"\u003cp\u003eThe Paxini DexH5 is PaXini's compact four-finger tactile dexterous robotic hand, with 9 degrees of freedom of which 5 are active and 528 ITPU multidimensional tactile sensing units integrated in one hand. It sits between a two-jaw gripper and a full five-finger hand: enough joints to grip, pinch, press and rotate objects, with touch feedback on every grasp.\u003c\/p\u003e\u003cp\u003eFingertip force is controlled to 0.1 N, which PaXini designed for delicate operations. High-strength composite materials and a bionic multi-joint structure keep the hand light, and coreless motors drive the five active joints. One hand carries up to 4 kg, opens around objects up to 10 cm across and completes an open-close in 1 s.\u003c\/p\u003e\u003cp\u003eEtherCAT and Modbus connect it to robot controllers and automation cells in manufacturing, logistics and research. Weight, supply voltage, hand side and mounting for your arm are confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eThe \u003ca href=\"\/en\/products\/paxini-dexh13-dexterous-robotic-hand\"\u003ePaxini DexH13\u003c\/a\u003e adds an 8 MP hand-eye camera, 16 degrees of freedom (13 active), 1,140 tactile units and a 5 kg payload, and the \u003ca href=\"\/en\/products\/paxini-gmh18-dexterous-robot-hand\"\u003ePaxini GMH18\u003c\/a\u003e moves to five fingers, 18 degrees of freedom and a 20 kg payload. Compare them with our other \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e528 tactile sensing units:\u003c\/strong\u003e One hand carries 528 ITPU multidimensional tactile units, so the hand feels contact as it grips.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.1 N force control:\u003c\/strong\u003e Fingertip force is controlled in 0.1 N steps, which PaXini designed for delicate handling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e5 active of 9 degrees of freedom:\u003c\/strong\u003e Five motors move nine joints in a four-finger bionic structure that grips, pinches, presses and rotates.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e4 kg payload:\u003c\/strong\u003e One hand carries up to 4 kg and opens around objects up to 10 cm across.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOpens and closes in 1 s:\u003c\/strong\u003e A full open-close takes 1 s, half a second faster than the DexH13.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLightweight composite build:\u003c\/strong\u003e High-strength composite materials keep the hand light for the arm that carries it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT and Modbus:\u003c\/strong\u003e Both protocols are supported for robot controllers and PLC-based automation cells.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Paxini","offers":[{"title":"Default Title","offer_id":67633071194342,"sku":"Paxini-DexH5","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/paxini_dexh5_dexh5.jpg?v=1791277774"},{"product_id":"paxini-gmh18-dexterous-robot-hand","title":"Paxini GMH18 Dexterous Robot Hand","description":"\u003cp\u003eThe Paxini GMH18 is PaXini's new-generation five-finger tactile dexterous robotic hand, with 18 degrees of freedom (11 active, 7 passive, five of them in the thumb) and over a thousand third-generation ITPU tactile sensing units covering the fingernails, fingertips, finger pads and palm. PaXini rates its payload at 20 kg, four times that of its four-finger DexH13.\u003c\/p\u003e\u003cp\u003eIt is built for research teams, integrators and manufacturers who need a strong hand that also feels. PaXini's force control algorithms adapt the grasp to the shape of each object, a self-locking mechanism keeps the grasp stable through long holds, and 15 kinds of tactile perception report contact right out to the fingernails.\u003c\/p\u003e\u003cp\u003eA built-in ARM SoC with pre-installed internal pose handles the hand's kinematics on board, so it works out of the box. Five protocols are supported (USB, EtherCAT, Ethernet, Modbus and CAN-FD), an embedded USB hub sends control, tactile and video signals down one output cable, and power comes from 24–48 V DC or USB PD 3.1. RGB, RGB-D or infrared cameras can be added on the palm side or the back of the hand. Weight, fingertip force and hand side are confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eFor four fingers, the \u003ca href=\"\/en\/products\/paxini-dexh13-dexterous-robotic-hand\"\u003ePaxini DexH13\u003c\/a\u003e pairs 1,140 tactile units with a fixed 8 MP hand-eye camera, and the \u003ca href=\"\/en\/products\/paxini-dexh5-dexterous-robotic-hand\"\u003ePaxini DexH5\u003c\/a\u003e is the compact 9-degree-of-freedom model. Compare them with the rest of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTactile from fingernail to palm:\u003c\/strong\u003e Over a thousand third-generation ITPU units cover the fingernails, fingertips, finger pads and palm, with 15 kinds of tactile perception.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e18 degrees of freedom, 5 in the thumb:\u003c\/strong\u003e Eleven active and seven passive joints, five of them in the thumb, let the hand adapt its grasp to the shape of the object.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e20 kg payload, self-locking grasp:\u003c\/strong\u003e PaXini rates the payload at 20 kg, and a self-locking mechanism keeps a grasp stable through long holds.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReady out of the box:\u003c\/strong\u003e A built-in ARM SoC with pre-installed internal pose handles the kinematics on board and runs PaXini's force control algorithms.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFive protocols, one cable:\u003c\/strong\u003e USB, EtherCAT, Ethernet, Modbus and CAN-FD are supported, and an embedded USB hub sends control, tactile and video signals down a single cable.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCamera expansion:\u003c\/strong\u003e RGB, RGB-D or infrared cameras mount on the palm side or the back of the hand for vision-guided grasping.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24–48 V or USB PD:\u003c\/strong\u003e The hand runs from a 24–48 V DC supply or a USB PD 3.1 power interface.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Paxini","offers":[{"title":"Default Title","offer_id":67633071259878,"sku":"Paxini-GMH18","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/gmh18_1.jpg?v=1791277773"},{"product_id":"x-square-artixon-five-finger-dexterous-robot-hand","title":"X Square ArtiXon Five-Finger Dexterous Robot Hand","description":"\u003cp\u003eThe X Square ArtiXon is X Square Robot's five-finger dexterous robotic hand: a tendon-driven hand with 20 degrees of freedom moved by 15 actuators, at a weight under 1 kg. X Square rates it for 31 kinds of dexterous manipulation, including pinching, grasping and twisting, with a 3–5 kg payload and repeatability under 1 mm.\u003c\/p\u003e\u003cp\u003eTouch is built into every fingertip. The sensors measure normal and shear force from 0.1 to 20 N at ±0.1 N accuracy and detect an object about 1 cm before contact, and grip strength can be adjusted while the fingers move. That makes the ArtiXon a fit for research labs, embodied-AI teams and service-robot developers who handle fragile objects, tools and everyday items rather than one fixed part.\u003c\/p\u003e\u003cp\u003eTendons with micro reducers open and close the fingers in under a second, and real-time closed-loop control runs at 100 Hz over USB 3.0. ROS1 and ROS2 are supported and X Square provides a plug-and-play SDK. A self-locking mechanism holds a grasp without continuous power, cutting standby power consumption by 80 %, and the hand is rated for 1,000,000 cycles. Supply voltage, hand side and mounting for your robot are confirmed with the quotation.\u003c\/p\u003e\u003cp\u003eTo compare the ArtiXon with other tendon-driven and tactile hands, see our full range of \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e20 degrees of freedom, 15 actuators:\u003c\/strong\u003e A 20-joint bionic frame driven by 15 actuators performs 31 kinds of manipulation, from pinching and grasping to twisting.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFingertip force from 0.1 N:\u003c\/strong\u003e Sensors in the fingertips measure normal and shear force from 0.1 to 20 N at ±0.1 N and detect objects about 1 cm away.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTendon drive under a second:\u003c\/strong\u003e Tendons with micro reducers open and close the fingers in under a second, and grip strength can be adjusted while the hand moves.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelf-locking grasp:\u003c\/strong\u003e The hand holds a grasp without continuous power, which X Square rates as an 80 % cut in standby power consumption.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e100 Hz over USB 3.0:\u003c\/strong\u003e Real-time closed-loop control runs at 100 Hz over a high-bandwidth USB 3.0 link.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eROS1, ROS2 and a plug-and-play SDK:\u003c\/strong\u003e ROS1 and ROS2 support and X Square's SDK bring the hand into an existing robot software stack.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRated for a million cycles:\u003c\/strong\u003e X Square rates the hand at 1,000,000 cycles, with repeatability under 1 mm and a weight under 1 kg.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"X Square","offers":[{"title":"Default Title","offer_id":67633079189734,"sku":"X-Square-ArtiXon-Hand","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/x-square-artixon.jpg?v=1791277782"},{"product_id":"inspire-rh56bfx-dexterous-robot-hand","title":"Inspire RH56BFX Dexterous Hand","description":"\u003cp\u003eThe Inspire RH56BFX is the speed-focused dexterous robotic hand in Inspire Robots' RH56 series, which its maker calls the “Piano Hand”. Its four fingers flex at up to 570°\/s, and Inspire says that speed lets it win every round of vision-guided rock-paper-scissors against people. It comes as a left hand (RH56BFX-2L) or a right hand (RH56BFX-2R) and weighs 540 g.\u003c\/p\u003e\u003cp\u003eInspire built it for human-machine interaction: gestures and hand poses, interactive demonstrations, reception and guide robots, and light pick-and-place where response time matters more than grip force. Teleoperation and gesture research benefit from the same quick response.\u003c\/p\u003e\u003cp\u003eForce is the trade-off: 6 N at the thumb tip and 4 N at each fingertip, read at 0.5 N resolution by a force sensor on each of the six actuators, with absolute position sensors for real-time feedback. The thumb rotates laterally through more than 65° at 235°\/s and flexes at 150°\/s, and fingertips repeat to ±0.20 mm. Twelve joints fit in a 217.8 × 80.7 × 31.2 mm envelope, and a power-off self-lock keeps the last pose when the supply is cut.\u003c\/p\u003e\u003cp\u003eIt connects over RS-485 with an open register protocol at 115,200 bit\/s by default, with up to 254 hands on one bus, runs on 12–48 V DC with a 2 A peak at 24 V, and mounts by a Ø52 mm wrist flange. The \u003ca href=\"\/en\/products\/inspire-rh56dfx-dexterous-robot-hand\"\u003eInspire RH56DFX\u003c\/a\u003e uses the same frame and interface with 15 N at the thumb tip and 10 N per fingertip for firmer grasps, and the \u003ca href=\"\/en\/products\/inspire-rh56e2-dexterous-robot-hand\"\u003eInspire RH56E2\u003c\/a\u003e grips at 30 N. Browse the full range of \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e570°\/s finger flexion:\u003c\/strong\u003e The four fingers flex at up to 570°\/s, more than twice the 260°\/s of the RH56DFX.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMade for interaction:\u003c\/strong\u003e Inspire tunes the BFX for gestures and human-machine interaction and reports a 100 % win rate in vision-guided rock-paper-scissors.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuick thumb:\u003c\/strong\u003e The thumb rotates laterally through more than 65° at 235°\/s and flexes at 150°\/s.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLight grip by design:\u003c\/strong\u003e The thumb tip pushes with 6 N and each fingertip with 4 N, with force read at 0.5 N on each of the six actuators.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower-off self-lock:\u003c\/strong\u003e The fingers stay in their last pose when power is removed.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e540 g with RS-485:\u003c\/strong\u003e An open RS-485 register protocol, up to 254 hands per bus and a 12–48 V DC supply.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Inspire Robots","offers":[{"title":"Default Title","offer_id":67633586372838,"sku":"Inspire-RH56BFX","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/hand.jpg?v=1791277792"},{"product_id":"inspire-rh56dfx-dexterous-robot-hand","title":"Inspire RH56DFX Dexterous Hand","description":"\u003cp\u003eThe Inspire RH56DFX is a five-finger dexterous robotic hand from Inspire Robots' RH56 series, made as a left hand (RH56DFX-2L) or a right hand (RH56DFX-2R). Inspire presents it as the balance of strength and speed in the range: 15 N at the thumb tip, 10 N at each fingertip and four-finger flexion at 260°\/s, in a hand that weighs 540 g.\u003c\/p\u003e\u003cp\u003eSix micro linear servo actuators move 12 joints, with absolute position sensors and a force sensor on each actuator for real-time force feedback at 0.5 N resolution. Give each finger a force threshold and it stops when it gets there, so firm and soft objects, a mug, an apple, a drill handle, are gripped by force rather than by position alone. A power-off self-lock holds the fingers in place, and the hand needs no repositioning when power comes back.\u003c\/p\u003e\u003cp\u003eThe hand is 217.8 mm long, 80.7 mm across the palm and 31.2 mm thick, and mounts on a Ø52 mm wrist flange with four 3.5 mm and four 6.0 mm holes. Fingertips repeat to ±0.20 mm; the thumb rotates laterally through more than 65° at 107°\/s and flexes at 70°\/s. Control runs over RS-485 at 115,200 bit\/s by default (8 data bits, no parity, 1 stop bit) with an open register protocol, up to 254 hands on one bus and stored action sequences of up to eight gestures. The supply range is 12–48 V DC, with a 2 A peak at 24 V.\u003c\/p\u003e\u003cp\u003eThe \u003ca href=\"\/en\/products\/inspire-rh56bfx-dexterous-robot-hand\"\u003eInspire RH56BFX\u003c\/a\u003e shares this frame and weight but trades force for speed, with 570°\/s finger flexion and 6 N at the thumb tip. The \u003ca href=\"\/en\/products\/inspire-rh56e2-dexterous-robot-hand\"\u003eInspire RH56E2\u003c\/a\u003e is the heavy-load hand at 30 N per thumb tip, and the \u003ca href=\"\/en\/products\/inspire-rh56dfq-dexterous-hand-for-unitree-h2\"\u003eRH56DFQ configured for the Unitree H2\u003c\/a\u003e is offered for that humanoid. See all of our \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e15 N thumb, 10 N fingertips:\u003c\/strong\u003e The thumb tip pushes with 15 N and each of the four fingertips with 10 N.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e540 g with 12 joints:\u003c\/strong\u003e Six micro linear servo actuators drive 12 joints in a hand 217.8 mm long and 80.7 mm across the palm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eForce feedback on every actuator:\u003c\/strong\u003e Absolute position sensors and force sensors at 0.5 N resolution let each finger stop at a set force.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower-off self-lock:\u003c\/strong\u003e The fingers hold their position when power is cut and need no repositioning at power-on.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuick fingers and thumb:\u003c\/strong\u003e The four fingers flex at 260°\/s and the thumb rotates through more than 65° at 107°\/s, with fingertips repeating to ±0.20 mm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOpen RS-485 control:\u003c\/strong\u003e An open register protocol, up to 254 hands per bus and a 12–48 V DC supply keep integration simple.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Inspire Robots","offers":[{"title":"Default Title","offer_id":67633586471142,"sku":"Inspire-RH56DFX","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/inspire_6dfx.jpg?v=1791277792"},{"product_id":"shadow-dexterous-hand-dh-five-finger-robotic-hand","title":"Shadow Dexterous Hand (DH) Five-Finger Robotic Hand","description":"\u003cp\u003eThe Shadow Dexterous Hand (DH) is Shadow Robot Company's five-finger dexterous robotic hand, the full-size model of its Dexterous Hand series. It is built to the shape and size of a typical adult male hand and reproduces human kinematics with 24 joints: 20 driven by their own motors through tendons, plus four coupled movements that bend the fingertips the way a human finger does. It comes as a right hand, or mirrored as a left hand for two-handed systems.\u003c\/p\u003e\u003cp\u003eResearch groups use the Shadow Hand for grasping, in-hand manipulation, teleoperation, neural control and brain-computer interface work. Each finger has three degrees of freedom over four joints, the thumb five, an extra joint in the palm lets the little finger oppose the thumb, and two wrist joints help position the hand on a robot arm. Twenty Smart Motor units in the hand base each combine a Maxon motor, gearbox, tendon force sensing and electronics, close the torque loop at 5 kHz and can run at zero force so a joint can be back-driven. Every joint except the coupled fingertip joints is controlled to ±1°.\u003c\/p\u003e\u003cp\u003eMore than 100 sensors report at up to 1,000 Hz: a Hall-effect sensor on every joint at about 0.2°, 40 tendon load sensors at about 30 mN, an IMU, and Shadow Tactile Fingertips on the thumb and index finger with 17 three-axis taxels each. The hand talks to its control PC over 100 Mbps EtherCAT and is fully integrated with ROS, including a Gazebo model that runs the same code as the real hand. It weighs 4.3 kg with its forearm, holds up to 4 kg in a power grasp and runs from the 48 V supply provided.\u003c\/p\u003e\u003cp\u003eThe Shadow Dexterous Hand is sold by quotation, and its price follows the configuration: right or left hand, tactile fingertips on every finger, a bimanual pair, or the version Shadow integrates with a Universal Robots UR10e arm. For a lighter hand, the \u003ca href=\"\/en\/products\/shadow-dexterous-hand-lite-dhl-five-finger-robotic-hand\"\u003eShadow Dexterous Hand Lite (DHL)\u003c\/a\u003e keeps three fingers and the thumb at 2.4 kg, the \u003ca href=\"\/en\/products\/shadow-dexterous-hand-extra-lite-dhel-three-digit-research-hand\"\u003eExtra Lite (DHEL)\u003c\/a\u003e two fingers and the thumb, and the \u003ca href=\"\/en\/products\/shadow-dexterous-hand-extra-super-lite-dhsl-reduced-finger-research-hand\"\u003eExtra Super Lite (DHSL)\u003c\/a\u003e one finger and the thumb. The three-finger \u003ca href=\"\/en\/products\/shadow-dex-ee-dexterous-hand-robotic-research-platform\"\u003eShadow DEX-EE\u003c\/a\u003e is built for reinforcement-learning rigs; or compare our full range of \u003ca href=\"\/en\/collections\/robotic-hands\"\u003edexterous robotic hands\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey Capabilities\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e24 joints, 20 driven:\u003c\/strong\u003e Twenty motor-driven degrees of freedom and four coupled fingertip movements give the hand human kinematics, down to a two-joint wrist.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLittle-finger opposition:\u003c\/strong\u003e An extra joint in the palm swings the little finger toward the thumb, and the five-joint thumb opposes every finger.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTendon drive from 20 Smart Motors:\u003c\/strong\u003e Each motor unit combines motor, gearbox, tendon force sensing and electronics, closes its torque loop at 5 kHz and can run at zero force so a joint is backdrivable.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTactile thumb and index fingertips:\u003c\/strong\u003e Two Shadow Tactile Fingertips with 17 three-axis taxels each come fitted, and the other three fingers can take them too.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOver 100 sensors at up to 1 kHz:\u003c\/strong\u003e Hall-effect sensors read every joint to about 0.2°, 40 tendon load sensors resolve about 30 mN, and an IMU completes the set.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtherCAT and ROS from day one:\u003c\/strong\u003e The hand ships with an Ubuntu control PC, ROS drivers, Python and C++ access and a Gazebo model that runs the same code as the real hand.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRight, left or a pair:\u003c\/strong\u003e A mirrored left hand makes a bimanual pair, and Shadow offers the hand integrated with a UR10e arm as one ROS-controlled system.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis model is offered on a quotation basis. Configuration, accessories, integration scope and delivery schedule all change the final figure, so pricing is confirmed per project rather than listed.\u003c\/p\u003e\u003ch3\u003eBuying through Robotix Market\u003c\/h3\u003e\u003cp\u003eThis unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.\u003c\/p\u003e","brand":"Shadow","offers":[{"title":"Default Title","offer_id":67633592172774,"sku":"Shadow-DH","price":0.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/files\/shadow-robot_1_468c6e3e-e6c5-4907-8a04-4f6d2a1a45ba.jpg?v=1791277794"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0827\/3366\/2438\/collections\/hand_1.jpg?v=1794995987","url":"https:\/\/robotixmarket.me\/en\/collections\/robotic-hands.oembed","provider":"Robotix Market Middle East","version":"1.0","type":"link"}